3. A Long - shunt dynamo running at s00 r.p.mSupplres 20kw at a termi'nal voltage of 20ov.The vesistanees of the armature, shunt fieldひ te.ores pectively The overall e ffrerency at theabore Load is 85.. Find las Cu Ləssesiren a nd frietion Losses ee the torqueand senes frelod arelo0, andSo.oeserted by the prime motor.al far a

Answered: Image /qna-images/answer/92d698c3-8741-4239-8af2-464a635e610c.jpg

. A Long - shunt dynamo running Supplres 20kw at a terminal voltage at so0 ripim 200v. of The vesistances of the arma ture, shunt field ひ te.o ves pectively Thie overall e ffrerency at the above Load is 85.. Find las Cu L-sses iren a nd friction Lasses Le the torque and senes freld are u lool So o serted by the Prime motor cations

. A Long - shunt dynamo running Supplres 20kw at a terminal voltage at so0 ripim 200v. of The vesistances of the arma ture, shunt field ひ te.o ves pectively Thie overall e ffrerency at the above Load is 85.. Find las Cu L-sses iren a nd friction Lasses Le the torque and senes freld are u lool So o serted by the Prime motor cations

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A 40kW induction motor with a lagging power factor of 0.76 is supplied by a 120Vrms 60Hz sinusoidal voltage source. find the capacitance needed in parallel with the motor to raise the power factor to (a) 0.9 lagging and (b) 1.0
Does Clampor circuit change the peak-to-peak (i.e., rms value)? Justfy
H. W.: A 35 kW induction motor has power factor 0.9 and effliciency 0.9 at full-load, power factor 0.6 and efficiency 0.7 at half full-load. At no load the current is 25% of full-load current and power factor is 0.I. Capacitors are supplied to make the line power factor 0.8 at half full- load. With these capacitors in circuit, find the line power factor at: (i) full load, and (ii) no load.
The O.C.C. data for separately-excited generator when run at 130 r.p.m. on open circuit isE.M.F. (V) : 12 44 73 98 113 122 127Exciting current : 0 0.2 0.4 0.6 0.8 1.0 1.2Deduce the curve of e.m.f. and excitation when the generator is running separately-excited at 1000 r.p.m.To what voltage will the generator build up on no-load when running at 1000 r.p.m.? To what voltage will thegenerator build up on no-load when running at 100 r.p.m. if the total field resistance is 100 Ω ?
An ac controller has a resistive load of R = 10 2 and the input is 220 V, 50 Hz. The thyristors switch is on for n 25 cycles and for m 75 cycles. Determine: (i) (ii) (iii) the rms value of the output voltage, the input power factor, the average and rms current through thyristors.
The O.C.C. data for separately-excited generator when run at 130 r.p.m. on open circuit is E.M.F. (V) : 12 44 73 98 113 122 127 Exciting current : 0 0.2 0.4 0.6 0.8 1.0 1.2 Deduce the curve of e.m.f. and excitation when the generator is running separately-excited at 1000 r.p.m.To what voltage will the generator build up on no-load when running at 1000 r.p.m.? To what voltage will thegenerator build up on no-load when running at 100 r.p.m. if the total field resistance is 100 Ω ?
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 220 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. The maximum power that can be delivered to the load is: Select one: a. 5.65 kW b. 9.68 kW c. 11.52 kW d. None of these
6. Home Works: a) The figure below shows the per-phase equivalent circuit of a two- pole three-phase induction motor operating at 50 Hz. The voltage (E1) across the magnetizing inductance is 210 V, and the slip (s) is 0.05. What is the developed torque produced by the motor ? 0.04 0 jo.22 Q j0.22 0 j6.28 NE E1 0.05 0
A 6 pole wave wound d.c. shunt generator has 500 conductors. A generator delivers 50 kW of power at 250 voltage at full load. The resistance of the field circuit is 125 2. Actual brush shift is 10°. Then find the demagnetizing and cross magnetizing ampere turns per pole and how many additional turns must be wound on each pole to eliminate the demagnetizing effect.
A six pole, three-phase SCRIM is connected to 60 Hz supply. At full load the rotors induced emf makes 72 complete cycles in 1 minute. Find the rotor speed.
A synchronous generator is generating 395 V at 55 Hz at a field current of 3A. The e.m.f generated when the frequency is 35HZ and the field current is 2.3A is ..............
Two generators are supplying a load. Both the generators have a no-load frequency of61.5 Hz and the slope sp of 1 MW/HZ. If they are supplying a real load of 2.0 MW at 0.8 pflagging, what would be the system frequency and power sharing between two generators?What measures can be taken to make the frequency 60 HZ. If an additional 1.0 MW load isconnected to the existing one what would the system frequency be.