.16) A Wilson current mirror is designed with VDD = 5 volts, Vss = 0 v F 10 µA and all devices sized to 10 µm / 10 µm. = a. calculate the value of the small signal output resistance o Ilson current mirror. b. calculate the minimum output voltage, Vomin. c. Layout the devices M4 through M7, assuming that each device is ng an interditigated layout technique to match devices M5 and M6. Use allel devices for M4 and M7.

.16) A Wilson current mirror is designed with VDD = 5 volts, Vss = 0 v F 10 µA and all devices sized to 10 µm / 10 µm. = a. calculate the value of the small signal output resistance o Ilson current mirror. b. calculate the minimum output voltage, Vomin. c. Layout the devices M4 through M7, assuming that each device is ng an interditigated layout technique to match devices M5 and M6. Use allel devices for M4 and M7.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A circuit responding to temperature is shown in figure 6. Assume the diode equation is given by Ia Ioe(qVa/kT). What is the DC operating point of the circuit at the temperature T. Also determine the small signal output swing Av, due to an incremental change in temperature AT. For this question assume Rį = 0. Heat T+AT V. DD D'B R₁ OV +AV Figure 6: Temperature sensor
Q-1) Given a SCR that is in TO-3 package. In data sheet, Rejc is 2.5 °C/W, ReSA is 2.5 °C/W, and Recs is 1 °C/W. How much power will the SCR be able to dissipate and not exceed a junction temperature of 200°C if the ambient temperature is 40°C?
Soru 7 ID(sat.) is 0.0001 A (100 microA) for, and VG =6V for a long channel n-MOSFET with V= 1V. Calculate the saturation current ID(sat.)in units of microA if VG-VT=3V.
Explain the process of Transistor’s Engineering.
Problem-5 The LED in Figure below requires 30 mA to emit a sufficient level of light. Therefore, the collector current +Vcc should be approximately 30 mA. For the following circuit values, determine the Re amplitude of the square wave input voltage necessary to make sure that the transistor saturates. Use double the minimum value of base current as a safety ON ON margin to ensure saturation. OFF Vcc = 9 V, VCE(sat) = 0.3 V, Rc = 220 N, RB = 3.3 kÝ Bpc =50, and VleD = 1.6 V. 1
Fixed-bias Configurationa. What happen to the collector voltage, if the collector resistor is disconnected (open)? b. What happen to the base voltage if the base resistor is disconnected (open)?c. What happen to the collector voltage, if the collector resistor is shorted?
c. Draw the d.c load line for the circuit diagram shown below. What will be the Q point if zero signal base current is 25 HA and B = 60? (5 marks) Rc = 4 kQ NO SIGNAL V BB Vcc=12 V
In a two transistor model of SCR, the leakage current for transistor Q1 is 2 micro-ampere and the leakage current for transistor Q2 is two times of the leakage current of Q1. Given that the current gain for Q1 is 0.7 and the emitter current and gate current is 30 A & 0.25 A respectively. The anode current gain will be
how to draw the small signal model
Vin For the circuit shown, assume that Vo = 3V and that the transistor is described as follows: B-100, Va = 100V, VT = .025V. a) Determine the small signal parameters for the transistor. b) Draw the small signal model 5V 5V 300uA Vo www 4K 625 C
A Bipolar junction Transistor with curreat amplification factor being 100, Input Base current is 50μA. Collector voltage is 10 V and biasing voltage being +20 V. Find followings a. Collector current b. Resistance (R1) c. Collector voltage , Emitter voltage , Base Voltage & Collector-Emitter Voltage.
4 For the transistor shown in below figure, Calculate the value of R, that will just make the transistor work as closed switch. Hence Bpc= 80, VBE = 0.7V, VCE(sat) = 0.2V, Vcc= 12V, Rc= 2.7KN. la) Calculate the In and I.. Vcc RB Rc |b) Calculate Rp- B'