Solve Part 3 and Part 4 only IntroductionStructural analysis is important for designing all type of structure including truss structure. There are several methodto analyse truss structure. Therefore, student should be able to analyse the truss structure with appropriate method.This assignment is given to student to evaluate the ability of the student in solving the complex problem involvingtruss structure as shown in Figure 1 below.88)B001)6miv)JBy using an appropriate method,i)20KN♥6m20kN/mD30KNFigure 16mHFigure 1 above shows a truss structure, which is supported at A and G. The truss is design to support auniform load 20kN/m from C to E as shown in the figure. Given the elastic modulus, E=200GPa, and thecross-sectional area for member AJ, JI, IH, and HG is equal to 500mm² while other members is equal to250mm². Based on the details given, solve the following task to analyse the truss structure.Task 120KN6m8mDescribe the determinacy and stability of the truss structure. Your answer must be support bydetails explanation (CO1, C2, PO1, WP1)Show the internal force for each member in truss structure. Your answer must be include thefree body diagram of the structure, calculation of the reaction at support and detail calculationfor each joint (CO2, C3, PO2, WP1)Calculate the total vertical displacement at joint D if the all member is subjected to an increasein temperature of AT = +30°C, and member AB has been fabricated 5mm longer thanoriginal length. Given = 12 x 10-6 per °C. (CO3, C4, PO2, WP1)Determine the internal force for each member in truss structure if some members need to beremoved from the truss structure to decrease the cost of construction. Reminder that thebottom members and support must be remain as original structure. Your answer must beinclude with new truss modelling, details calculation of each joint and comparison with theoriginal truss structure (CO3, C4, PO2, WP2, WP3)

Answered: Image /qna-images/answer/faa15c60-4fdf-4ae9-886c-c5ae77c88913.jpg

0⁰) iv) Calculate the total vertical displacement at joint D if the all member is subjected to an increase in temperature of AT = +30°C, and member AB has been fabricated 5mm longer than original length. Given = 12 x 10-6 per °C. (CO3, C4, PO2, WP1) Determine the internal force for each member in truss structure if some members need to be removed from the truss structure to decrease the cost of construction. Reminder that the bottom members and support must be remain as original structure. Your answer must be include with new truss modelling, details calculation of each joint and comparison with the original truss structure (CO3, C4, PO2, WP2, WP3)

0⁰) iv) Calculate the total vertical displacement at joint D if the all member is subjected to an increase in temperature of AT = +30°C, and member AB has been fabricated 5mm longer than original length. Given = 12 x 10-6 per °C. (CO3, C4, PO2, WP1) Determine the internal force for each member in truss structure if some members need to be removed from the truss structure to decrease the cost of construction. Reminder that the bottom members and support must be remain as original structure. Your answer must be include with new truss modelling, details calculation of each joint and comparison with the original truss structure (CO3, C4, PO2, WP2, WP3)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the determinacy of plane structure as shown in the figure Pls answer problem 1&2
PLEASE SCAN OR ANSWER LEGIBLY THANK YOU (STRAIN/STRENGTH OF MATERIALS)
9:42 Von WiFi 83% 1) Justify the adequate of behavior of different structural material under different load conditions. 2) Determine shear force and bending moment value of statically determinate beam under Easily add text in PDF Add 5) Estimate load carrying capacity of column and strut subjected to axial loading using Euler and rankine theory. BV 2i To integrate quelities ike HUMANTY, SOCIAL VALUES, professional ETHICS and LEADERSHP in students in order to encourage contribution to Dciety. 13) To acquaint with moderm technicue and methad to emerge in acceptable dvil engineer in the competitive enviranment. 14) To collaborate with industry ard stakeholders for education, conultancy and research. (5) To encourage the students for higher studies. BHULABHAI VANMALIBHAI PATEL INSTITUTE OF TECHNOLOGY (DIPLOMA STUDIES) UMRAKH BIT . CIVIL ENGINEERING DEPARTMENT VISION: To be a centre of excellence to provide ethical professional diploma civil engineers. SEMESTER: 3rd COURSE NAME: STRUCTURAL…
SIMPLY SUPPORTED TRUSS how to get the values of RA AND RF in the computed values, please show the solution. the answers are given in the table
What is the midspan value of EI δ for the beam loaded as shown?
Question 24 Which one of these microfibrillar angles in the illustration is expected to be stronger in tension? A O a. A O b. B B
solve the given problem and show complete fbd and geometry of deformation
2. Determine the centroid for the following figure: 2.5 E2.5"- 1.5" 3"
Problem : In Fig.2 the undeformed configuration is outlined in solid lines and the deformed configuration in dashed lines. Calculate Yxy and Ex. y 150 mm 3 mm В 200 mm 3 mm Fig. 2 Page I 1
ANALYSIS OF TRUSS in A Example: Determine the forces in each member of the truss shown in the figure and indicate whether the member is in tension or compression. |l00 Ad 50 kN %23
A. diagram shows how the neutral surface of the structure changes shape under a given loading condition. Select the correct response: distributed load qualitative deflected shape bending moment shear
Two structural profiles have the same cross section. The difference between these two profiles, is in the height in relation to the axis that passes through the centroid of the flat surface. Profile A has a height of 20 cm from the centroid, while profile B has a height of 30 cm from the centroid line. Mark the correct answer and explain the reason for the choice.A) Two sections of different shapes, but with the same moment of inertia have equal resistance to bending.B) The profile with a higher height in relation to the centroid has a greater resistance module and, therefore, withstands less flexing efforts.C) Profile A, due to its lower relative height, is more rigid at the bending moment.D) The resistance to the rotation of a part depends exclusively on the moment of inertia of the plane surface of thesection.E) The profile with a higher relative height has a greater flexion resistance when subjected to efforts.