i need the answer quickly 02 Generator cost rate functions in $/hr for a three-unit system are given as follows:FI-0.008(P1)2 +0.5(P1) + 5, F2-0.030(P2)2 +0.2(P2) + 3, and F3-0.020 (P3)2 + 1.0(P3) + 5.These three generators must supply a total demand of 1100 MW. (a) Compute incremental fuelcost. (b) Determine the total cost rate.

Given data : Generator cost rate function are , F1=0.008P12 +0.5P1+5 F2=0.030P22+0.2P2+3…

02 Generator cost rate functions in $/hr for a three-unit system are given as follows: FI-0.008(P1)2 +0.5(P1) +5, F2-0.030(P2)² +0.2(P2) + 3, and F3=0.020(P3)2 + 1.0(P3) + 5. These three generators must supply a total demand of 1100 MW. (a) Compute incremental fuel cost. (b) Determine the total cost rate.

02 Generator cost rate functions in $/hr for a three-unit system are given as follows: FI-0.008(P1)2 +0.5(P1) +5, F2-0.030(P2)² +0.2(P2) + 3, and F3=0.020(P3)2 + 1.0(P3) + 5. These three generators must supply a total demand of 1100 MW. (a) Compute incremental fuel cost. (b) Determine the total cost rate.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.49P

See similar textbooks

Similar questions

two alternators A and B having 5% speed regulation are working in parallel at a station. Alternator A is rated at 15 MW while B is at 20 MW. When the total load to be shared is 12 MW, then how much of the load will be shared by the alternator B?
The reactance of a generator is given as 0.25 per-unit based on the generator’s of 18 kV, 500 MVA. Find its per-unit reactance on a base of 20 kV, 100 MVA. a. 0.0505 b. 0.0605 c. 0.0405 d. 0.0606
Q31 Generator cost rate functions in $/hr for a three-unit system are given as follows: Fl=0.004(P1) +5.3(P1)+500, F2=0.006(P2)² + 5.5(P2) + 400, and F3-0.009(P3)°+ 5.8(P3)+ 200 These three generators must supply a total demand of 975 MW. (1) Conpute 2. (i) Determine the total cost rate.
The one-line diagram of a simple power system is shown in Figure below. The neutral of each generator is grounded through a current-limiting reactor of 0.25/3 per unit on a 100-MVA base. The system data expressed in per unit on a common 100-MVA base is tabulated below. The generators are running on no-load at their rated voltage and rated frequency with their emfs in phase. G Stark Item Base MVA Voltage Rating X' x² 20 kV 20 kV 20/220 kV 20/220 kV 100 0.05 0.15 0.15 0.10 0.10 220 kV 0.125 0.125 0.30 0.15 0.25 025 0.7125 0.15 100 100 0.15 0.05 0.10 0.10 0.10 100 0.10 100 100 Lu La 220 kV 0.15 220 kV 0.35 100 A balanced three-phase fault at bus 3 through a fault impedance Zf= jo.I per unit. The magnitude of the fault current in amperes in phase b for this fault is: Select one: A. 345.3 B. 820.1 C. 312500 3888888 产产

The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
Two 60MVA, alternators operate in parallel. The setting of the governor are such that the rise in speed from full load to no load is 2% in one machine and 3% in the other, the characteristics being straight lines in both cases. If each machine is fully loaded when the total load is 120MW, what will be the load on the first machine (with 2% speed regulation) when the total load is reduced to 80MW?
2. If the generator cost function of three generators are given as: C1 = 472.8 + 7.47 P1 + 0.023 P,2 (OMR/h/MW) C2 = 432.9 + 7.87 P2 + 0.020 P,2 (OMR/h/MW) C3 = 463.9 + 7.56 P3 + 0.022 P,2 (OMR/h/MW) Find the optimal dispatch of the three generators. Total load demand is 1800 MW.
In a given system of base power of 250 MW, and bus 3 is taken as reference. The per-unit reactances are X12 = 0.2 p.u., X13 = X23 = 0. 1 p.u. The power flow in the system is given as: PF12 = 50 MW, PF13 = 150 MW, PF23 = 50 MW. Based on readings from 2 meters (not including M12 meter), M13 = 145 MW (not calibrated), and M23 = 50 MW (well calibrated), deduce the flow on line 1-2. Select one: O a. PF12 = - 47.5 MW. O b. None of these O c. PF12 = 67.5 MW. O d. PF12 = 47.5 MW. O e. PF12 =- 57.5 MW. O f. PF12 = 57 MW.
Two similar 2,500 kW, 3 phase generators operate in parallel. The speed load characteristic of the first generator is such that is no-load frequency of 60.5 Hz drops uniformly to 58.5 Hz at full load, while for generator 2, its no-load frequency of 60.5 Hz drops uniformly to 59 Hz at full load. Determine the kW load of each generator if the combined load is 4,000 kW. a. 1,714.3, 2,285.7 b. 2,015.5, 1,984.5 c. 1,765.5, 2,234.5 d. 2,452, 1,548
Select generator rating as base value
10. What is the angle of lead ? (DC GENERATOR QUESTION)
Problem 2 Two shunt generators A and B operate in parallel and their load characteristics maybe taken as straight lines. The voltage falls from 240V at no load to 200V at200A, while that of B falls from 245V at no load to 220V at 150A. Determine the bus bar voltage when supplying 66.9KW load. How is the load divided between two generators?