Please answer all subpart either dislike is ready..Please ok 1) A 240V / 60Hz single-phase voltage source supplies 2 loads in parallel. The first draws 6 kWand 4 kVAr while the second consists of an RC load (3 2 and 3mF).a. Compute the values of the basic elements of load #1.b. Calculate the active power and power factor of load #2.c. Compute the power factor seen by the source, stating if it is leading or lagging.d. Draw the phasor diagram of the system, showing the source voltage and current as wellas the currents of the 2 loads. Use the source voltage as reference phasor.e. Provide expressions for the instantaneous values of the source voltage and current aswell as the currents of the 2 loadsf. Sketch the waveforms (time domain) of the source voltage as well as the currents inboth loads.

We are authorized to answer three subparts at a time, since you have not mentioned which part you…

1) A 240V/60Hz single-phase voltage source supplies 2 loads in parallel. The first draws 6 kW and 4 kVAr while the second consists of an RC load (3 2 and 3mF). a. Compute the values of the basic elements of load #1. b. Calculate the active power and power factor of load #2. c. Compute the power factor seen by the source, stating if it is leading or lagging.

1) A 240V/60Hz single-phase voltage source supplies 2 loads in parallel. The first draws 6 kW and 4 kVAr while the second consists of an RC load (3 2 and 3mF). a. Compute the values of the basic elements of load #1. b. Calculate the active power and power factor of load #2. c. Compute the power factor seen by the source, stating if it is leading or lagging.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
A parallel connection of a RL branch with a C branch is connected across a 100V AC mains. At first R = 10 ohms, L = 20mH and frequency of 1000rad / s, the current measured is 2.2361A at 89.44 leading power factor. A) Determine the initial capacitance. B) However, a fault occurs on the capacitor branch making its capacitance 20% lower and a resistance of 5 ohms is detected. If this faulty circuit is rerun but at a frequency of 500 rad / s, determine the new current that will flow through the circuit.
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Alternator A (100 kVA, 3-f, 240 V, 60 Hz, 1800 rpm) is operating in parallel with alternator B (125 kVA, 3-f, 240 V, 60 Hz, 1800 rpm). The load of alternator A is 70 kW at 85% pf leading and the load of alternator B is 85 kW at 75% pf leading. Determine the pf of load.
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
The reactance of a generator is given as 0.1 pu based on the generator of 17 KV, 300 MVA. Determine the pu reactance on a base of 17 KV, 250 MVA. New pu reactance is.......