(1) A cantilever steel beam with the triangular cross section is loaded with the concentrated force as shown. The modulus of elasticity for steel is 30 million psi and Poisson's ratio is 0.28. The second area moment of triangular beam about is centroid is I= bh³/36 (b: width, h: height). Find the stress state at point M within the cross-section B. 4 ft 4 ft 200 lb N.A. Cross section M 2 in 1 in 1 in 1 in

(1) A cantilever steel beam with the triangular cross section is loaded with the concentrated force as shown. The modulus of elasticity for steel is 30 million psi and Poisson's ratio is 0.28. The second area moment of triangular beam about is centroid is I= bh³/36 (b: width, h: height). Find the stress state at point M within the cross-section B. 4 ft 4 ft 200 lb N.A. Cross section M 2 in 1 in 1 in 1 in

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.5.2P: A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is...

See similar textbooks

Similar questions

Find expressions for shear force V and moment M at v = L/2 of beam AB in structure (a). Express V and M in terms of peak load intensity q0and beam length variable L. Repeat for structure (b) but find Fand M at m id-span of member BC.
The cross section of a composite beam made of aluminum and steel is shown in the figure. The moduli of elasticity are TA= 75 GPa and Es= 200 GPa. Under the action of a bending moment that produces a maximum stress of 50 M Pa in the aluminum, what is the maximum stress xs in the steel? If the height of the beam remains at 120 mm and allowable stresses in steel and aluminum are defined as 94 M Pa and 40 M Pa, respectively, what heights h and h. arc required for aluminum and steel, respectively, so that both steel and aluminum reach their allowable stress values under the maximum moment?
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0,5 in, is subjected to internal pressure p = 375 psi, In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure), (a) Determine the maximum tensile stress ctniXand the maximum in-plane shear stress Tmjv in the wall of the cylinder. (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T\ (c) If 7 = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness
(1) A cantilever steel beam with the triangular cross section is loaded with the concentrated force as shown. The modulus of elasticity for steel is 30 million psi and Poisson's ratio is 0.28. The second area moment of triangular beam about is centroid is - bh³/36 (b: width, h: height). Find the stress state at point M within the cross-section B. | 4 ft 4 ft 200 lb N.A. Cross section M 2 in 1 in 1 in 1 in
A cantilever steel beam with the triangular cross section is loaded with the concentrated force as shown. The modulus of elasticity for steel is 30 million psi and Poisson’s ratio is 0.28. The second area moment of triangular beam about is centroid is I= bh3/36 (b: width, h: height). Find the stress state at point M within the cross-section B.
As shown in the figure below, determine the internal loadings at points D and. Consider the weight of the beamwhich is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
Q / The figure below shown that the three bars are supported a rigid beam ACE. The bar CD is made of steel and bars AB and EF are made of aluminum. If each bar has 10 mm diameter, find the maximum value of force F if the permissible stress for steel and aluminum are 190 MPa and 120 MPa respectively. Known the modulus of elasticity for steel and aluminum are 180 GPa and 60 GPa respectively (B F al st al 180 cm E 0.7 m 0.7 m 0.7 m 0.7 m F 2F
A bending moment due to load applied on the head of femur bone which is offset by a distance (x= 50 mm) off the bone center for a person standing in relaxation.His weight is 70kg.1. Find the maximum bending stress induced due to the weight and compare it to the maximum comp. stress. R= 20mm t= 12mm.2. Draw the expression for the second moment (I) basing on min-wall hollow cylinder.3. Find the principal stress σ1, σ2, τx1y1, and the angle θp for point C and D shown.
For the beam below find the normal stress at sections in point (B) and (C) D. B 75 kN 35 kN 45 kN 85kN D=40mm D=80mm 1m 2m 1m
(ohsm 2) b. throps A simply supported beam has a rectangular cross-section of 50 mm wide and 120 mm deep. It is loaded as shown in Fig. 3b. Calculate the maximum stresses and draw the stress distribution diagram. The weight of the beam is assumed negligible. mot dit to sbutingsm s A - 2 m edband Im 10 kN B Fig. 3b 136 say xovbizon 2 m C
For the beam shown at right, determine the following: P= 1800 lb a. Maximum tensile bending stress b. Transverse shear stress at a the junction of the "TEE" (i.e., 2" above the neutral axis). c. Transverse shear stress at the neutral axis - 7.5 ft- - 7.5 ft- (a) d. Draw the stress elements -10 in. representing the state of stress at the junction of the “TEE" and at the neutral axis. | 2 in. 4 in. -N- 1600 10 in. 8 in. 42 in.k- (b)