1) A circular steel bar 50 mm diameter and 200 mm long is welded perpendicularly to a steel plate to form a cantilever to be loaded with 5 kN at the free end. Determine the size of the weld, assuming the allowable stress in the weld as 100 MPa.

1) A circular steel bar 50 mm diameter and 200 mm long is welded perpendicularly to a steel plate to form a cantilever to be loaded with 5 kN at the free end. Determine the size of the weld, assuming the allowable stress in the weld as 100 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A butt weld is set on the cross section of an I-shaped beam. There are bending moment M and shear force V at the splicing position, where M=1120 kN•m and V= 374 kN. The beam is made of Q355b steel and semi-automatic weld is used with welding rod E50. The design value of the weld tensile strength f," is 260 N/mm². Please check whether the strength of the butt weld is safe by calculation. 280 M M 0001
An aluminum alloy [E-10,000 ksi; Oy- 40 ksi] pipe (1) is connected to a bronze [E-16,000 ksi; Oy - 45 ksi] pipe at flange B. The pipes are attached to rigid supports at A and C. Pipe (1) has an outside diameter of 2.425 in., a wall thickness of 0.21 in., and a length of L₁ - 8 ft. Pipe (2) has an outside diameter of 5.00 in., a wall thickness of 0.20 in., and a length of L₂ - 14 ft. If a minimum factor of safety of 2.1 is required for each pipe, determine: (a) the maximum load P that may be applied at flange B. (b) the deflection of flange B at the load determined in part (a). Deflection to the right is positive. (1) (2) C L2 Answer: (a) P- 80.4 (b) UB-i | L₁ P B kips ! in.
O wrapping the weld around the corner a minuimum of the specified weld size and ar wrapping the weld around the corner for a distance not less than two times nor mor QUESTION 4 On all CJP groove welds in butt joints transverse to the computed tensile stress, they:. O A. Shall have no visible porosity that exceeds 1/32" O B. shall have no visible porosity that exceeds 3/32" O C. shall have no visible porosity O D. shall not have a sum of visible porosity that exceeds 3/8" O E. shall not have a sum of visible porosity that exceeds 1/2" QUESTION 5
Q1. Well water contained in an AISI 304 SS pipe network for chemical treatment and posterior distribution by aerial water pipes to different locations in a food manufacturing facility was analysed. The AISI 304 SS pipe network had an approximate 300 m length, 154 mm diameter and 2.0 mm wall thickness. The AISI 304 SS pipes were welded using a Tungsten Inert Gas (TIG) welding procedure. In-situ weld quality assurance was tested by pressurized WW, and no pinhole leakage was detected. After the pipe network remained out of service for 6 months at room temperature containing stagnant, pressurized well water, pitting corrosion was observed on the weld joints and the base material by the presence of multiple pinhole leaks.(a) Discuss, with chemical equations if relevant, TWO corrosion events that may have caused the pitting corrosion.(b) What practical steps could have been taken to mitigate for this potential outcome?(c) Identify corrosion inhibition methods to mitigate for the corrosion…
Find. The weld sizé W for the welted.join .shawai figure T=2 Nimっ below where aaill =3.MPag Tall=1.5 Mfa F=500 N ..in. D = l00 mm 2 6. =300M m %3D Ans: h=9.1 mm 4s0.707t A TO @ab ending
The beam shown is 1000 mm long with cross section of 50 mm by 100 mm, and is subjected to a load of 500 kgs. A 7018 electrode is used to weld the beam section all around [as shown]. Weld size is 12 mm. Approximate the maximum stress in the weld. Compare the maximum weld stress with the strength of the electrode. 12 F 1000 100
An AISI 1050 HR solid tube of 20mm diameter is acted by force F1 = IkN, and force F2 of 2kN. The tube is welded to a larger round base by 3mm fillet weldment, the base is connected to the ground base (shown in gray color) by means of four bolts M8x1.25mm (property class of 4.8)). The bolts are evenly distributed at 20mm away from the center of the tube. R=100 F1 120 120. F2 R=100 D =20 120 R=3 D =60 40 Dimensions are in mm Perform the following the following: 1- Find the state of stress for the most critical point on the assembly and build the mohr's circle. Solve question 1
Problem 3.1: Determine the design strength of a 1 mm length of a 6.35 mm fillet weld formed by the shielded metal arc process (SMAW) and E70 electrodes with a minimum tensile strength Fexx = 483 MPa. Assume that the load is to be applied parallel to the weld length. Problem 3.2: Repeat problem 3.1 if the weld is 500 mm long. Problem 3.3: Repeat problem 3.1 if the weld is 750 mm long. Problem 3.4: Repeat problem 3.2 if the application of the load is at an angle of 35 degrees from the longitudinal axis of the weld. Problem 3.5: Repeat problem 3.3 if the application of the load is at an angle of 35 degrees from the longitudinal axis of the weld.
2. A circular steel bar (50 mm) diameter and (200 mm) long is welded perpendicularly to a steel plate to form a cantilever to be loaded with (5 kN)at the free end. Determine the size of the weld, assuming the allowable stress in the weld as (100 MPa). [Ans. 7.2 mm]
An aluminum alloy [E = 10,000 ksi; oy= 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi; Oy= 45 ksi] pipe at flange B. The pipes are attached to rigid supports at A and C. Pipe (1) has an outside diameter of 2.475 in., a wall thickness of 0.19 in., and a length of L1 = 10 ft. Pipe (2) has an outside diameter of 4.60 in., a wall thickness of 0.18 in., and a length of L2 = 17 ft. If a minimum factor of safety of 1.8 is required for each pipe, determine: (a) the maximum load P that may be applied at flange B. (b) the deflection of flange Bat the load determined in part (a). Deflection to the right is positive. (1) B L2 Answer: (a) P = i 34.1 kips (b) uB = i .319 in.
sheet Hw Asteel bar of rec tangular crossl seetion with dimension as -s hownin fig- belo .This bar is Connected toawell. Using welded Juin along the sides only- find the weld size Ch) .where: Tall= 75 N /m? answer h= 4.04 %3D %3D F=213.3 N yomm 50omm l0omm
7. In a Lancashire steam boiler, there is a ------- at the end of the fire grate which is utilized in deflecting the flue gases upwards. 8. There are geothermal resources named ----- contain hot liquid water at temperatures up to 450 K and pressures up to 60 MPa. 9. There are fine flat plates in the combustion chamber of a single-ended scotch marine boiler. These plates require ----------. 10. The main objective of the ---------- is to protect the turbines against the water hammer effect at the time of starting or shutting off the hydroelectric power plant. 11. Based on the furnace position, Cornish boiler is classified as ‒‒‒‒‒‒‒‒‒‒‒