1-AQ/ 10. A wire 50.0 m long and 2.00 mm in diameter is connected Tto a source with a potential difference of9.11 V, and the cur- rent is found to be 36.0 A. Assume a temperature of 20.0°C and, using Table 26.2, identify the metal out of which the wire is made. 10) snu be est lar R-Ro ent 11. An electric heater carries a current of 13.5 A when operat- 11) of 5 heater?

1-AQ/ 10. A wire 50.0 m long and 2.00 mm in diameter is connected Tto a source with a potential difference of9.11 V, and the cur- rent is found to be 36.0 A. Assume a temperature of 20.0°C and, using Table 26.2, identify the metal out of which the wire is made. 10) snu be est lar R-Ro ent 11. An electric heater carries a current of 13.5 A when operat- 11) of 5 heater?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- A). Which of the following could be used as a discharge device in an inductive AC circuit? a) resistor b) diode c) metal oxide varistor d) "a" and "c", not "b" B. What is the purpose of a discharge device used in conjunction with opening a highly inductive circuit? a) to minimize the possibility of damage to the circuits insulation as a result of a high induced voltage b) to minimize the possibility of endangering the life of the person opening the controlling switch c) to allow the magnetic field to gradually collapse, thus limiting the value of the self-induced ernf d) all of the above C. The high voltage induced by an inductor when its circuit is opened could be used constructively for a) an automotive ignition system b) an electric fence c) both "a" and "b" d) neither "a" nor "b"
Discuss the relationship between voltage break down and humidity, temperature and distance explain with curve
8. Liquids with solid impurities a) Have higher dielectrie strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average dc voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
Magnetically coupled circuit example
An iron core 0.4m long and 5 cm2. In cross section, is wound with 300 turns. When a current of 0.5 A flows in the coil, how much is the inductance of the coil. Assume the core has a permeability of 2500. Ans 350mH
We want to investigate how the field strength will be with air as dielectric and with steatite. A plate capacitor is placed in a 24 kV network between phase and ground. The relative permittivity of air is &=1 and for steatite &-6. The plate capacitor has area = 1m². The distance between the electrodes is 2 mm. Ep = 8.854-10-12 F/m A=1m² d=2mm a) Calculate the maximum field strength in the plate capacitor. (Answer: 9.8kV/mm) b) What is the capacitance of the capacitor if we use steatite? (Answer: C = 26.6nF)
A 120 V, 60 W lamp is to be operated on 220 V, 50 Hz supply mains. For the lamp to operate in correct voltage, calculate the value of (i) non-inductive resistance and (ii) pure inductance (U.P.T.U. 2005–06)
Which of the following is not true for ferromagnetic materials? Please choose one: a. High?mthey have value. b.Above the Curie temperature, they lose their non-linear properties. C. a fixedµrthey have value. D.The energy loss is proportional to the area of the hysteresis loop.
c) A platinum coil has a resistance of 3.146 at 40°C and 3.767 at 100°C. Find the resistance at 0°C and the temperature -coefficient of resistance at 40°C.
A coil consists of 2000 turns of copper wire having a cross-sectional area of 0.8 mm2. The mean length per turn is 80 cm and the resistivity of copper is 0.02 un-m. Find the resistance of the coil and power absorbed by the coil when connected across 110 V d.c. supply.
k) A coil consists of 2000 turns of copper wire having a cross-sectional area of 0.8 mm2. The mean length per tum is 80cm and the resistivity of copper is 0.02u 52-m. Find the resistance of the coil and power absorbed by the coil when connected across 110v d.c. supply.
Please give explained solution