Given the truss below what are the internal force members of members BF, AB and AD. Determine whether compression or tension.|– 3 m →— 4 m —✦✦3 m →|BсA60 kNFAB = Blank 1 kNFAD = Blank 2 kNFBF = Blank 3 kNED+3 m4 m3 mI

Name: Given the truss below what are the internal force members of members
Uploaded: 2024-03-05T11:56:34.000Z
Channel: Bartleby
Description: Given the truss below what are the internal force members of members BF, AB and AD. Determine whether compression or tension.|– 3 m →— 4 m —✦✦3 m →|BсA60 kNFAB = Blank 1 kNFAD = Blank 2 kNFBF = Blank 3 kNED+3 m4 m3 mI

Answered: Image /qna-images/answer/bdf2488e-cfe3-4949-9a7d-15e860479b50.jpg

Answered: 1 | 3 m+4 m3 m B 0 60 kN E C D T 3 m 4…

Science

Physics

1 | 3 m+4 m3 m B 0 60 kN E C D T 3 m 4 m 3 m

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 67PQ

See similar textbooks

Similar questions

Determine the normal force N inside each bar Sa function of the external force P 1.5 m 2 m Probs. 1-40/41/42
Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm2 for AB and 400 mm2 for AC. Determine the maximum safe value of W if the working stresses are 110 MPa for AB and 120 MPa for C 60° 40°/ W 95,215.23 KN 87,721.45 KN 98,134.53 KN 90,675.78 KN
Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have, and specify where D must be located for a strut of this length to be used. Take x= 120 mm. 60 mm D. y 20 mm E The smallest length CD may have is mm. The coordinates of point Dare ( and Imm.
A bar ACB has is subjected to an external load at C, and it is supported either end by a cable as shown in fig. below. Calculate the smallest area of each cable if the stress is not to exceed 90 MPa in bronze and 120 MPa in steel. Bronze 5m Steel 3 m 4 m C 8m B 12m 10 KN
PROBLEM 2. The light rigid bar ABCD shown in Fig. P-252 is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P = 41. 29 KN is applied. Hint: convert the distance of each member into mm, area of steel and aluminum into mm^2, & E into MPa.. Steel L-3 ft A- 0.5 in E- 29 x 10° psi 4 ft Aluminum L-4ft A- 0.75 in E - 10 x 10 psi + 2 ft Figure P-252
The truss is made of three A-36 steel members, each having a cross-sectional area of 400 mm2. Determine the magnitude P required to displace the roller to the right 0.2 mm.
Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the glass stays approximately rigid. Determine the average shear strain in the nylon due to the load P when the assembly deforms as indicated. 2 mm 3 mm 5 mm 3 mm 5 mm 3 mm 0.197 rad 0.297 rad O 0.397 rad O 0.125 rad O none of the above
The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. Determine the length L that results in portion BCD of the wire being horizontal. 200 mm -L- В D IC 150 mm A
help me pls
The beam is supported by a pin at A and a short link BC. Figure 1 of 1 > 0.5 m Tadika 1m 1.5 m 1.5 m H. Part A If P = 13 kN, determine the average shear stress developed in the pins at A, B, and C. All pins are in double shear as shown, and each has a diameter of 17 mm. (Figure 1) Enter your answers separated by commas. TA. TB. TC = Submit Provide Feedback 197| ΑΣΦ | 11 | vec Request Answer MPa I
12:10 4G Not Secure - yslphysics.weebly.com the rod. odulus for metal = 1.0 x 10!l N m²² ) 30 of 32 Answer: 3.2×10-4 J EXERCISE 2 A hollow cylinder has length 50.0 cm, internal diameter 5.0 cm and external diameter 6.0 cm. A force of magnitude 1.0 kN acts at each end of cylinder so that the cylinder is being compressed. Determine the compression of cylinder. ( Young's modulus for the material of the Cylinder = 7.0x101º Nm-² ) Answer: 8.3×10-6 m EXERCISE 3 A wire of length 0.50 m is fixed horizontally between two supports separated by 0.50 m. When a mass of 8.0 kg hangs from the middle of the wire, the mid-point sags by 1.00 cm. The diameter of the wire is 2.8 mm. Calculate the Young's modulus of the wire. (Given g = 9.81 m s-2) Answer: 1.99 × 10* Pu
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. A stainless steel tube with an outside diameter of 46 mm and a wall thickness of 5 mm is used as a compression member. If the axial stress in the member must be limited to 362 MPa, determine the maximum load P that the member can support. O 194 KN O 142 kN Ea O 233 KN O 219 KN O 295 KN