1 Problem54State, x(t)SAWNO-Nw.●●Case 1O 26Time, sec.underdampedcritically dampedState, x(t)• overdamped54321 ONS TYCase 22 ▷Time, sec.8 10State, x(t)52 + 34Case 32 ▷6Time, sec.5432State, x(t)& A & No.2Match each of the resposes above to one of the following second-order system types:• undampedCase 4▷Time, sec.

Answered: Image /qna-images/answer/5c5a7934-fb66-4826-85e6-eba944d3757b.jpg

1 State, x(t) Problem 5 4 3 -5 O 2 Case 1 Time, sec. underdamped 5 4 3 critically damped overdamped State, x(t) i'r AW NO 2 Case 2 Time, sec. State, x(t) 5 4 32 2344 -5 O Case 3 2 ▷ 6 Time, sec. State, x(t) 543210 234 Case 4 Match each of the resposes above to one of the following second-order system types: • undamped 2 ▷ 6 Time, sec.

1 State, x(t) Problem 5 4 3 -5 O 2 Case 1 Time, sec. underdamped 5 4 3 critically damped overdamped State, x(t) i'r AW NO 2 Case 2 Time, sec. State, x(t) 5 4 32 2344 -5 O Case 3 2 ▷ 6 Time, sec. State, x(t) 543210 234 Case 4 Match each of the resposes above to one of the following second-order system types: • undamped 2 ▷ 6 Time, sec.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q.11 - Consider the positions servomechanism is shown in figure below. Assume the following numerical values for the system constant are. Kp = gain of potentiometer detector = 7.64 v/ rad, Kb= back e. m. f. constant =5.5*10-2 V/rad/sec K; = motor torque constant = 6*10–5 Nm/A C = 4*10-2 Nm/ (rad /sec). Determine the natural frequency and damping ratio of the system. Ra = armature winding resistant =2 2, Ka=Gain of amplifier = 10 Jm = 1*10-5 Kg.m2. J =4.4*103 Kg.m2 n = gear ratio=1/10, Neglect Cm and la Amp. %₂ ဦးအောင်မျိုာနစ် နှစ် DH 0050 constant N₁
20 The particular integral for an damped single degree of freedom system subjected to a harmonic force F = F, Cos w,t, is given by a. x,(t) = (F/k)cosot b. x,(t) = A sin(o,t +p) c. x,(t) = A cosot d. x,(t) = X cos(@t -0)
1. Obtain the non-periodic B-spline curve of order 4 is defined by four control points: P0=(0,0,0), P1=(6,8,0), P2=(12,8,0), P3=(18,0,0) a. Rotate the curve around x axis by 180 degrees. b. Rotate the control points and obtain the B-spline after the rotation. c. Compare the B-spline equations obtained in a and b
A 3-phase I.M. operate at 400 Hz has a rated speed 10800 R.P.M, its speed at slip = 0.7 is equal to: O3400 R.P.M. O3600 R.P.M. O3800 R.P.M. O None.
15 The solution to free vibration of a damped single degree of freedom system is a. x(t) = Ae"Sin(o,t+n) b. x(t) = Ae"Sin(o,t+2) c. x(t) = ASin(@,t+o) d. x(t) = Ae"Sin(o,t+q) %3D
Compute the maximum percent overshoot 100Mp and the 2% settling time ts that correspondto wn = 1 ???/???, damping ratio= 0.707.
20 C {K A sin wt Calculate the damping factor () with the following data Ft= 501b = e = 10em w. = ? k = 22016/in C = 200 200 lb/in 4 = ?
QUESTION 1 Consider a 2 DOF system shown below. X1 k₁ m1 F₁ k₂ X2 k3 m₂ F2 The modeshape can be written as (1))] What is x for the second modeshape? Use scientific notation with 3 significant digits and omit units. (eg. -0.123) Let m1 = 2, m2 = 2, k1 = 9, k2 = 8, and k3 = 8.
Find natural frequency
19 We obtain thẹ differential equation: mä+ bi+ kx = 0, Pas a model for a spring-mass-damper system with: m:=2, k=18. ww à) Identify thë damping constant b that gives rise to critical damping, b) If, instead, b=24, approximately how long will.it take for the the amplitude of free vibration to be reduced to within 2% of zero?
Plz solve within 30min I vill give definitely upvote and vill give positive feedback thank you Take F1=170lb F2=210lb,and F3=160lb
- Consider the positions servomechanism is shown in figure below. Assume the following numerical values for the system constant are. Kp = gain of potentiometer detector = 7.64 v/ rad, Kb = back e. m. f. constant -5.5*10-2 V/rad/sec K₁ = motor torque constant = 6*10-5 Nm/A C₁ = 4*10-2 Nm/ (rad /sec). Determine the natural frequency and damping ratio of the system. Amp. % Ra= armature winding resistant =20, Ka=Gain of amplifier =10 Jm= 1*10-5 Kg.m². J₁=4.4*10-³ Kg.m² n = gear ratio=1/10, Neglect Cm and la constant 0050 N₁ DI