1) Three pipes in series of L=600ft with D=20", L=4000ft with D=16", and L-2000ft with D=12". All pipes are new cast iron pipes with C-130. Convert the system to: a) an equivalent length of 16" pipe. b) an equivalent size pipe with 12000ft long. Assume Q=2 ft³/sec. Use: D = 1.375 C-0.38 Q0.38 S-0.205

1) Three pipes in series of L=600ft with D=20", L=4000ft with D=16", and L-2000ft with D=12". All pipes are new cast iron pipes with C-130. Convert the system to: a) an equivalent length of 16" pipe. b) an equivalent size pipe with 12000ft long. Assume Q=2 ft³/sec. Use: D = 1.375 C-0.38 Q0.38 S-0.205

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9/3 Pipes Figure below:- 3 Pipes Connected in Series as shown in the 0 L₁ = soom d₁ = 0.06 m f = 0.02 → 3 Q=0-0117(m²³ / $) L₂=700m d₂= 0.08 m f = 0.02 L3= 600m d₂=0-m f = 0.02 Required: Diameter of the equivalent pipe for these 3 pipes to carry the same (@) and has the Same length (Summation of length of these 3 pipes).
Q1: The figure below shows a regulator, determine whether the structure is safe against piping or not and design the thickness of floor by using Lane's method. (c=8.3) EL.=103 EL=101 EL.-100 EL.=98.5 3.0 1.5 1.0 5.0 -2.0 7.5 7.0
Q1: Find the equivalent pipe for the loop shown below, also find the pressure at point C if the pressure at point A is 450 kpa. Use CHw=100 for all pipes. BC AC V=1 m/sec Pipe AB Diameter 250 153 200 Q=252 m/hr A (mm) Length (m) 500 1000 500
Ex Convert the piping system to an equivalent length of 6" pipe. Factors K Strainer B 12" Bends C, F (each) 12" Tee D = 8.0 = 0.5 = 0.7 = 1.0 12" x 6" Cross G(xV /2g) = 0.7 = 6.0 = 0.5 = 3.0 12" Valve E 150-12"(f=0.025)- 6" Meter H 6" Bends J, K (each) 6" Valve L 100-6"(f= 0.020)
Pipes in Series h₂ 2₁ ● ● = र N EL H.G.L 3 B
The steel pipe shown carries water from the main pipe A to the reservoir and is 2 inch in diameter and 240 ft long. What must be the pressure in A to provide a flow of 45 gpm? Clevation K00 t Water 7 50 F Open globe valve 90 bends (threaded)- Elevtion 20 fr 2 in galvanizcd pipe
find Q ? and pressure at each pipe L: 7om dsolm L=ioum
A 60-inch main carrying 90 cfs branches at a point x into two pipes, one 1,000 ft. long 4 ft. in diameter and one 4,000 ft. long 2 ft. in diameter. Both pipes come together at a point y and continue as a single 60-inch pipe. Assuming the values of the friction factor f as 0.02, 0.022, and 0.024, respectively, for the 60-in., 48-in., and 24-in. pipes, compute the rate of flow in pipe 3 in cfs. Round your answers in 2 decimal places.
FLUID FLOW IN PIPES I. Proving. SHOW THAT 21 5.v=R3S2 → hf n 10.29n²LQ² D16/3
%TE l, UPUOM A 9;Y) 团 / د امتحان مد1.docx The pipe assembly is subjected to the force of F = {600i + 800j – 500k} N Determine the moment of this force about point B. 0.5 m 0.4 m 0.3 m 0.3 m II
Q2: An otl of viscosity Co.15 pas) and specific gravity 0.9 is flows Throngh 1.Find The slope of The Pipe That will canse The Pressure to be constantalong The pipes entire length? an inclined (300mm) diameter Pipe. Q= 0.005m3/sec 3oomm Dia. Zz datum 2. check if The Rlow is laminarRlow?
QI: Find the equivalent pipe for the loop shown below, also find the pressure at point C if the pressure at point A is 450 kpa. Use CHw=100 for all pipes. ВС AC V=1 m/sec Pipe AB Diameter 250 153 200 (mm) Length (m) Q=252 m/hr A 500 500 1000