1. A 100 MVA, 20 kV alternator has X 1 = X 2 = 0.20 pu and X 0 = 0.05 pu. The neutral of the generator is grounded through a reactor. Find the ohmic value of reactor to limit the current for a single line to ground fault equal to the current for a three-phase fault.

1. A 100 MVA, 20 kV alternator has X 1 = X 2 = 0.20 pu and X 0 = 0.05 pu. The neutral of the generator is grounded through a reactor. Find the ohmic value of reactor to limit the current for a single line to ground fault equal to the current for a three-phase fault.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.32P: Determine the positive- and negative-sequence phase shifts for the three- phase transformers shown...

See similar textbooks

Related questions

Q: 6. Use Kirchhoff's Laws to calculate the potential difference and the current across each resistor…

A: Given data, Circuit diagram is given as,

Q: Q4/ For the network in Fig.4 1. Write the equations necessary to solve for the branch currents. 2.…

A: Current: It is the time rate of the change of the charges. It flows from high voltage to low voltage…

Q: For a frequency of 200 Hz, the time period will be (a) 0.05 s (b) 0.005 s (c) 0.0005 s (d) 0.5 s

A: Given: Frequency, f = 200 Hz

Q: B. Explain essential parts of communication system

A: Solution- A communication system is used to transfer information between two points- Basic…

Q: Q6) Find the skin depth & and propagation constant at a frequrnvy of 2MHz in copper where o =…

A: 6) To find the skin depth and propagation constant Given , frequency = 2 MHz in copper

Q: Find the RMS value of the current waveform and the average power absorbed by the 9 ohms resistor if…

A: In this question we need to find a RMS value of the given waveform and average power.

Q: 4. Find v and ic for t> 0 if i (0) = 1A and v(0) = 8V. 4H { 20 ww 250 mF + > 802 w

Q: O Final Task #2 63 61 ба 4G6 + 64 65

A: Block Diagram Reduction Rules Follow these rules for simplifying (reducing) the block diagram, which…

Q: + 2 V1 10Vrms 50Hz 0° V1 = 10 /0° R1 100 Ω R2 10002 L1 320mH C1 16µF

Q: Am 11 KV /33 KV 220 MVA, 60 Hz transformer is wooded at sy. with resistive to ad Ratio 21 KW at…

A: In this question we need to find a copper loss at 50% and 75% loading

Q: First question: Distributor (AB) fed from one end Find the distribution of currents and voltages on…

Q: A DC shunt motor is supplied by 250-volt and 15kW at rated load, if the No-load speed is 10 r.p.m…

Q: PRACTICE PROBLEM 2.1: For the circuit shown below, calculate the voltage v, the conductance G, and…

Q: A depletion MOSFET with IDSS=12mA, VP=-4V is operated at VGS=-0.5V. What is the value of…

A: The transconductance of the JFET is determined using the expression shown below:…

Q: Q2) A DMS sends a message with alphabet size equal to 6 symbols at 100 symbols/secs. Symbol k is…

A: DMS Sends a message with alphabet size equal to 6 symbols at 100 symbols/sec. symbol k is repeated k…

Q: A) Determine the z-transform for (Choose one only) 1. x(n) = 6(0.6)" cos (0.2лn)u(n) 2. x(n) = 4e-3n…

A: In this question we will find z transform of given function....

Q: *LINE 1 P 1 KW consuming Q=1 KVAR consuming *LOAD 1 P 5 KN consuming Q =9.45 KVAR delivering *LINE 2…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: The maximum efficiency of a 500 – kVA, 3300/500 V, 50 Hz, single phase transformer is 97% and occurs…

A: Given maximum efficiency ηmax=97% at 3/4 of full load kVA rating of transformer =500kVA impedance…

Q: It is required to know 1. The Real Power of the Generator: 2. The Reactive Power of the Generator 3.…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 05/ Using a 4-Y or Y-A conversion, find the current I in each of the networks in Fig. 5. www 4 kfl…

Q: 2. A 100 MVA, 18 kV generator, with per unit reactance of X”d = 0.19, X’d = 0.26, and Xd = 1.3 is…

A: In this question we need to find the initial symmetrical rms current in the line on the low voltage…

Q: Q5/ Using a A-Y or Y-A conversion, find the current / in each of the networks in Fig. 5. 4kfl www…

A: In this question, We need to determine the current I in the shown the circuit using the star to…

Q: Q Draw the bounce diagram for the transient circuit of the figure below, including the first four…

Q: The force between two charges is 120 N. if the distance between the charges is doubled, the force…

A: We need to find out force between two charge particles for given distance between them

Q: Please send the Design of the tank as photo or PDF file the Design sketch of the tank is require…

A: The diagram of the tank is presented in the following section.

Q: 8- Inter pole winding is connected in a) series with armature c)parallel with armature 9- What are…

Q: Example 33.7. A 5,000-kVA, 3-phase transformer, 6.6/33-kV, NY, has a no-load loss of 15 kW and a…

A: Delta star connection of transformer- In case of the delta-star connection of a 3-phase…

Q: Z (Z-0.25) (Z-0.5) a find xing when ROC is for Home work: for X(Z) = non - Causal

Q: 4. A receiver has 2 uncoupled tuned circuit before the mixer, each with a Q of 75. The signal…

A: For the above given question we need to calculate the value of image rejection ratio by considering…

Q: 3. Using superposition, find the current I through the 24 V source in Fig. 9.121. E₁ = + 42 V R₁ 118…

A: Superposition Theorem When Multiple voltage and current source are present in the electrical…

Q: Calculate current 122 ha Timo R Viza =C ext) = 100√2 sin (wt + 80) 12 2₁-50 Ze = -50. Z₂ 60 R = 80…

A: Given: Consider the following circuit: To find: The current IL2.

Q: does TP4056 can prevent 3.7v li-ion battery from overcharging? What is the maximum voltage of the…

A: Given We need to determine whether TP4056 can prevent 3.7v li-ion battery from overcharging and…

Q: What is the expression of the complex power of the reliant current source? 103 16.52 2014 2020°V 6Vx…

Q: 1- In d.c. generator, the neutral plane shifts in opposite the direction of rotation 2- Imno-load…

A: In this question we will write answers related to generator, motor , transformers.... Note :- as per…

Q: An electron in a TV picture tube moves toward the front of the tube with a speed of V = 5.10 m/s.…

A: Given data, Charge on electron q=1.6×10-19 C Velocity of electron v=5×106 m/s Magnetic field B = 0.1…

Q: 1. Mark on an Argand diagram the points representing the following numbers: (a) 2 (b) 3i (c)-i (d)…

Q: Home work for X(Z) = Z (Z-0.25) (Z-0.5) find xing when ROC is for and unstable system. a non-causal

Q: 41. What is the potential difference from point b to point d in the circuit shown? Which is at high…

A: We need to find out the potential difference between given point

Q: Q2: Assuming an ideal diode, sketch vi, vd, and id for the half-wave rectifier 7. The input is a…

Q: The current at resonance in a series L-C-R circuit is applied olta

A: At resonance, inductive reactance is equals to capacitive reactance. Before resonance on increasing…

Q: An electron in a TV picture tube moves toward the front of the tube with a speed of V = 5.10 m/s.…

A: We will find out magnetic force.

Q: Example:. Find A (cl)? 12. 10 5 2 A Op-amp w 7 TO V₂

A: In this question, We need to determine the Voltage gain of the op amplifier? We are solving this…

Q: If resonant frequency, wo = 1100 rad/s, find the following: a) L in mH; b) Quality factor Q; c)…

A: The circuit diagram is shown below, Where,ωo=1100 rad/secandIt=cos 1050t+cos1400t A

Q: 5. Use Kirchhoff's Laws to calculate the potential difference and the current across each resistor…

A: In this question, We need to determine the potential difference and current in the each resistance…

Q: A) Determine the z-transform for (Choose one only) 1. x(n) = 6(0.6) "cos (0.2mn)u(n) 2. x(n) = 4e-3n…

A: In this question we will find z transform of given function.... You want one only so I will post z…

Q: Find v, for the circuit below. 5 0 10 sin (5000) 30°) V + 40 μF 80 2 sin (8000 + 10°) A

A: In this question, We need to determine the voltage v as shown the circuit using the super position…

Q: 2.3. A 44/11 K JJ KV, JMVA, so Hz Single following winding distance transformer has the resistence &…

A: Given data, Voltage rating 44/11 KV KVA rating S = 1 MVA Resistance and reactance of primary side of…

Q: HW: Determine the output expression if NAND gates are used in Fig. 3-26. A B C D E F G H a a +Vc Q…

A: By using concept of wired logic we need to derive the output Boolean expression for the given logic…

Q: What distance should a 2N load placed from the pivot so that the see saw won't move? 0.3 m ? m 3N O…

A: We need to find out distance for 2N force .

Q: 2.10. H.W. Working in the s-domain, find the Norton equivalent connected to the 1 resistor in the…

A: In this question we need to find a Norton equivalent circuit across 1 ohm resistor in S - domain

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

1. A 100 MVA, 20 kV alternator has X 1 = X 2 = 0.20 pu and X 0 =
0.05 pu. The neutral of the generator is grounded through a
reactor. Find the ohmic value of reactor to limit the
current for a single line to ground fault equal to the
current for a three-phase fault.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1Introduction

VIEW

Step 2 Calculation

VIEW

Step 3 Result

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the positive- and negative-sequence phase shifts for the three- phase transformers shown in Figure 3.36.
Question 6 What is phase angle of voltage induced in primary and secondary windings of transformers due to mutual flux? Same Opposite Zero None of option A Moving to another question will save this response. AR e IT:7
What is phase angle of voltage induced in primary and secondary windings of transformers due to mutual flux? Same Opposite Zero None of option
Loss of excitation is one of the stator faults of alternator which is operational at power station O True False
A 400 V, 3-phase alternator is subjected to an unsymmetrical fault. The sequence currents are Ia1= -j10 A, Ia2 = j6 A and Iao = j4 A. The sequence impedances are Z1 = j10 ohm, Z2 = j5 ohm and z0 = j7.5 ohm. Find the fault current and the type of fault. Also find the terminal voltages (phase and line) of the generator.
In small transformers, the total copper loss may vary from the rated output. % of O 0.2 to 0.6 O 0.5 to 1 O 0.8 to 1.5 O 0.4 to 1
For the same alternator the ratio of rated kva, when connected as a three phase winding alternator to when connected as a single phase alternator by using all the coils is
In single phase power factor meter there is error due to frequency and waveforms but not in three phase power factor meter, I know the reason why?? Please elaborate properly
Q5/C: Compare between Auto transformers and 2 winding transformers.
A generator supplies a motor through a Y-A transformer. The generator is connected to Y side of the transformer. A fault occurs between the motor terminals and the transformer. The symmetrical components of the subtransient current in the motor flowing toward the fault are: I =-0.8- j2.6pu I =-j2.0pu I =-j3pu From the transformer toward the Fault: I = 0.8– j0.4pu I? =-j1.0pu 1 = Opu Assume X =X,=X, for both the motor and the generator. (a) Describe the fault type and find the prefault current, if any, in line a. (b) Determine the subtransient fault current in per unit. (c) Calculate the subtransient current in each phase of the generator in per unit taking into consideration the phase shift of the Y-A transformer.
A three-phase 50 MVA 10 kV generator has a reactance of 0.2 pu per phase. Hence the per-unit value of the reactance on a base of 100 MVA 25 kV will be
Eniya.R ons Subject test Note:- You are attempting question 1 out of 12 For the same alternator, the ratio of rated KVA, when connected as 3-phase winding alternator to when connected as single phase alternator (by utilizing all the coils) is, (a) 1.33 (b) 0.50 (c) 0.67 (d) 1.50 Answer CA O D Subr 16