1. (a) Calculate the pore pressure, the total stress, and the effective stress at the indicated points in the figures below. (b) Determine the head loss, the hydraulic gradient, and the discharge velocity in each layer. (c) evaluate the possibility of quicksand in scenarios (a) and (b) if the head difference increases.

1. (a) Calculate the pore pressure, the total stress, and the effective stress at the indicated points in the figures below. (b) Determine the head loss, the hydraulic gradient, and the discharge velocity in each layer. (c) evaluate the possibility of quicksand in scenarios (a) and (b) if the head difference increases.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.1P

See similar textbooks

Similar questions

Determine the following: a) hydraulic conductivity is ______ x10^3 cm/sec b) Transmissbility of the impermeable layer is _____ cm^2/sec c) The drawdown in the test well is ____ m
An oil having viscosity 0.08 N-s/m2, specific weight 8829 N/m³, density 900 kg/m³ flows at the rate of 5.4 x 10-3 m³/s through a horizontal circular pipe of 0.12 m diameter and length 150 m. Find, (i) pressure difference in 150 m length in kN/m² (ii) wall shear stress in N/m² (iii) average and maximum velocity
CVE 331: Theoretical hydraulic conductivity calculation Problem 1: The hydraulic conductivity of a sandy sol is 7x10 cm/sec at void ratio 0.68. What is the hydraulic conductivity at void ratio 0.85 ? (o.re) A= 2,42e k2 ei Problem 2: The hydraulic conductivity of a clay soil is 121o* cm/sec at void ratio 0.56, and 3.1x10 cm/sec at void ratio 0.74. What is the hydraulic conductivity the soll at void ratio 0.65 ? e3 ki %3D - 3. 797 GRAIN SIZE DISTRIBUTION GRAPH. A- PROJECE
B. Under certain conditions the Thiem equation (5-43) for confined aquifers, is equivalent to the Cooper-Jacob equation (5-58) for confined aquifers. What are the conditions? (This exercise is easier than Problem A.) C. If an analysis is made of the hydraulic conductivity of a site using permeameter tests of core samples, slug tests of monitoring wells, and pumping tests of production wells, it is often observed that the hydraulic conductivity as measured by each method is different. Which method would be most likely to have the greatest hydraulic conductivity, and which the least? What are some possible reasons why this would be true?
Question 13 Which of the following best decreases the hydraulic radius? O increasing the depth decreasing the depth O increasing the width O decreasing the width
If H₁ = 3ft, H₂= 3.4ft, h = 2.43ft, Ysat-118.80lb/ft3, area of the tank = 8.91ft², and hydraulic conductivity of the sand k = 0.43ft/min. The seepage force per unit volume is lb/ft3? Inflow Valve (open)
A sand sample of 35m cm^2 cross sectional area and 20cm long was tested in a constant head permeameter. Under a head of 60 cm, the discharge was 120 ml in 6min. The dry weight of sand used for the test was 1120 g, and Gs= 2.68 A. Determine the hydraulic conductivity in cm/sec. B.Determine the discharge velocity in cm/sec. C. Determine the seepage velocity in cm/sec.
1. In a system with 4 reservoirs and 1 pipe junctions, how many hydraulic headloss equations are formulate? A. 3B. 2C. 1D. 4E. 5 2. In turbulent flow, which is correct?BJ: higher Re value has lower friction factorJB: lower Re value has lower friction factorGroup of answer choices A. BJ is true and JB is false B. BJ is true and JB is true C. BJ is false and JB is false D. BJ is false and JB is true 3.which of the following is always the same for horizontal closed conduit? A. Total headB. Velocity headC. Elevation headD. Pressure head
1. For a constant head laboratory permeability test on a fine sand, the following values are given: L = 300 mm; D₁ = 200 mm; h = 400 mm; Vol = 420 m³; t = 4 min; e = 0.55. a. Compute the coefficient of permeability in cm/sec. b. Compute the discharge velocity in cm/sec. c. Compute the velocity. seepage 2. For a falling head permeability test, the following are given. Length of specimen is 380 mm, are of specimen - 6.5 cm², hydraulic conductivity of soil specimen is 0.175 cm/min. a. What should be the area of the stand pipe for the head to drop from 650 cm to 300 cm in 8 min?
Determine the increase of pore water pressure at M due to the infinite strip loading shown in Figure Q3. Assume y= 0.5 and A-0.6. Im Clay 4m 2m 9-100kN/m² 4m Figure Q3 M G.W.T.
In the heterogeneous system shown below, 1-D groundwater flow is perpendicular to layers of varying hydraulic conductivity. K1 = 0.5cm/sec; K2 = 0.10cm/sec; K3 = 0.25cm/sec and b1 = 20 m; b2 = 40 m; b3 = 60 m Ah, Ahz Ah3 K1 K2 K3 b1 b2 b3 a) The flow across the system q is 0.03cm/sec/m². Using Darcy's Law, find the change in head Ah across each layer. b) Find the effective hydraulic conductivity (Ke) for an equivalent homogeneous system, that is, a system with the same total gradient and flow rate as the heterogeneous system.
At n = 0.45, the hydraulic conductivity of the sand is 0.010 cm/sec. Determine the hydraulic conductivity at n = 0.50.