1. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress In the tube when the power is transmlt- ted through a 4 :1 gearing. [Ans. 30 MPa]

1. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress In the tube when the power is transmlt- ted through a 4 :1 gearing. [Ans. 30 MPa]

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Related questions

Q: Given data: Maximum shear stress-50 MPa Maximum principal stress=80 MPa Find minimum principal…

Q: Given a shear stress of txy 5000 psi and a shear modulus of G 1.15 x 107 %3| psi, find the shear…

A: Shear stress, τxy=5000 psiShear modulus, G=1.15*107

Q: Compute: a.) The maximum shear stress developed in a 6 inch diameter solid steel shaft that…

Q: Suppose that P = 40 kN . (Figure 1) Part A Determine the principal stress developed at point A on…

A: Given data,P=40 kNM)a-a = P×300=40×103×300= 12×106 N-mm

Q: 4. Compute for the induced stress, in MPa, of a steel solid shafting of 6 cm diameter and 5 m in…

Q: Find the shear stress in 10 mm diameter shaft subjected to 2 kW power transmission at 100 rpm.

A: Given data:

Q: A tiramisu cake has a top area of 1500 mm2 and a height of 30 mm. When a shearing force of cN is…

Q: A shaft is required to transmit 285 kW power at 255 r.p.m. The maximum torque may be 1.8 times the…

A: Given that , Power P=285KW=285×106N-mm/sShear stress σs=46Mpa=46N/mm2Angle of twist…

Q: keyed sprocket delivers a torque of 778.8 N-m thru the shaft of 54 mm OD. The key thickness is 1.578…

A: Given:Torque delivered by keyed sprocket, T=778.8 N-mouter diameter of shaft, d=54 mm or 0.054 mkey…

Q: A 4-T crane is used to lift a 3m x 1.2m x 200mm pre-cast panel. A spreader beam is needed to ensure…

Q: Q2: A solid steel shaft 450 mm long is stressed at 75 MPa when twisted through 3° and used to…

Q: A rectangular key was used in a pulley connected to a line shaft at 23 HP and 10 rps. If shearing of…

Q: 1. Calculate what horsepower a solid steel shaft 6 inches in diameter can transmit at 160 rpm if the…

Q: A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be…

A: Now since at every point, it is assumed that the particles of materials are in equilibrium, the…

Q: 3- A steel shaft in a conveyor transmits 30 hp of power at 5 Hz. Determine the smallest safe…

Q: A hollow steel shaft, 12 m long, is required to transmit 1000 kW when running at a speed of 300…

A: Given that , L=12m =12000mm P=1000 kW =1000×106N-mm/s

Q: A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under…

A: Calculate the strain in the wire. ε=δll Here, l is the original length of the wire, δl is the change…

Q: For the punching operation shown in the figure, compute the shear stress (in GPa) in the material if…

A: GivenP=5500kNt=1.5mm=0.0015md=15mm=0.015mL=20mm=0.020m

Q: A shaft running at 700 r.p.m transmits 18 kW. Assuming allowable shear stress in shaft is 70 N/mm²,…

Q: A shaft running at 400 r.p.m. transmits 10 kW. Assuming allowable shear stress in shaft as 40 MPa,…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: Two 30 mm thick plate is fastened by two bolts, 25 mm in diameter. If the plate is subjected to 50…

A: The given design problem may be solved as :

Q: 8. Find the minimum size of a hole that can be punched in a 20 mm thick mild steel plate having an…

Q: 48 kN, D=17 mm A) find the cutting force in the n-n section. find as kN B) find the shear stress of…

Q: A shaft of diameter 40 mm is subjected to 360 N-m torque. The length of the shaft is 10 cm.…

A: Given data: The diameter of the shaft, d = 40 mm. The torque subjected to the shaft, T = 360 N-m.…

Q: A motor drives a shaft at 56 Hz and delivers 11 kW of power (see figure). 56 Hz 11 kW (a) If the…

Q: A shaft is required to transmit power 1MW at 240r.p.m. The shaft must not twist more than 1 degree…

Q: A shear force of S, = 35 kN is applied a distance of a/2 to the left of the vertical mid-line, as…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: 2. A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is…

A: Given data:

Q: stanchion and carries a vertical load of 50 kN. Assuming that the total shearing stress in a bolt is…

A: GIVEN:

Q: 26. If ơ, = 50 ksi, oy = 10 ksi, and Txy = 30 ksi, what is the absolute maximum shear stress for the…

A: Given: The stress along x-axis, σx = 50 ksi The stress along y-axis, σy = 10 ksi The shear stress,…

Q: The four gears are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of…

Q: A hollow 3 m long steel shaft that will provide the main engine drive transmission for a ship to be…

A: Given data: Length of hollow steel shaft, L=3 m=3000 mm. Torque requirement is, T=25 kN.m=25×106…

Q: 1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20…

A: Given data diameter of shaft (d) = 80 mm maximum shear stress in shaft (τmax) = 63 MPa width of…

Q: Format TL GyabGSkin -a-0630b/a) 60 MPa 45 MPa My 100 MPа 100MPA w-, cos20 + tysin20, oun =% * °%,…

A: Given Data The stress acting in x direction is: σx=100 MPa. The stress acting in y direction is:…

Q: You are an engineering intern at a manufacturer of mechanical tools, your senior engineer asked you…

A: Data given - d = 20 mm Di = 75 mm L = 250 mm F = 4kN

Q: Problem #7: For the structure below find the maximum absolute vertical shear stress (Oxy) anywhere,…

A: Draw the F.B.D of the given beam and calculate the reactions. For the equilibrium of the given…

Q: A shaft running at 400 r.p.m. transmits 10 kW. Assuming allowable shear stress in shaft as 40 MPa,…

A: GivenN=400rpmP=10kWσa=40MPa

Q: The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure…

Q: uter diameter 60 mm and inner diameter 40 mm) is running at 43 Hz. If the shaft transmits 156 kW,…

Q: ssume oz = 500, oy = 300, Tzy = 250, Oyicld = 350. Answer the following questions. Click here for…

A: Given Data⇒ σx=500 MPaσy=300 MPaζxy=250 MPa

Q: 3. Given a shear stress of Txy = 5000 psi and a shear modulus of G = 1.15 x 107 psi, find the shear…

A: As per our guidelines, we are supposed to answer only first one question in case of multiple…

Q: 8.20 At a certain point on the outside of a shaft, which is subjected to a torque, and a bending…

Q: A 1.25 in.-square steel punch is to push through an aluminum plate that is supported on a die, thus…

A: Given The side of the square steel punched part is s=1.25 in. The allowable compressive strength is…

Q: b a A steel shaft of solid elliptical cross section has a semi-major axis of length, a, and a…

A: Given , length of the major axis , a =25 mm Length of the minor axis , b =13 mm Torque , T=550…

Q: Reproduce Figure 2.23 twice, first adjusting it so that it accurately depicts the case in which the…

A: For the first case, it is given that the horizontal stress is half of the vertical stress that means…

Q: A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under…

A: Given: Young's modulus (E)=8.5×106N/m2Original length (L)=1.5mElongation (δ)=2.5mm or 0.0025m

Q: the shearing stress caused by a torque of 700 N m if dimension a =75 339. A tube 3 mm thick has the…

Q: Q1. Find the shear stress in aluminum and Steel TAl, TS Use: Gsteel = 85 GPa, GAI= 30 GPa

Q: 1. (20 p.) In the figure below, a built-in bar of length L 600 mm is forced by a force that makes…

Q: 2: ural stress which fluctua MN/m2 and - 115 MN/

A: Givenflexural stress σ1=250MN/m2σ2=-115MN/m2yield strength σy=0.55σultEndurance strength…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

shaft, If the ratio of the Inside to the outside dlameter is 0.4.
[Ans. 35 mm ; 90 mm]
4. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine
develops 10 kW at 2000 r.p.m. Find the maximum shear stress In the tube when the power is transmlt-
ted through a 4:1 gearing.
[Ans. 30 MPa]
A cylindrical shaft made of steel of vield strength 700 MPa is subtected to static loads consisting ofa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A shaft running at 400 r.p.m. transmits 10 kW. Assuming allowable shear stress in shaft as 40 MPa, find the diameter of the shaft. [Ans. 35 mm]
A shaft is transmitting 100 kW at 180 r.p.m. If the allowable stress in the material is 60 MPa, find the suitable diameter for the shaft. The shaft is not to twist more than 1° in a length of 3 metres. Take C= 80 GPa. [Ans. 105 mm]
A hollow steel shaft transmits 600 kW at 500 rpm. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque The answer is 100mm and 50 mm. can you help me this calculation and i give the answer already. and write with pen. tqvm
EXERCISES 1. A shaft rumning at 400 r.p.m. transmits 10 kW. Assuming allowable shear stress in shaft as 40 MPa, [Ans. 35 mm] find the diameter of the shaft. 2. A hollow steel shaft transmits 600 kW at 500r.p.m. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque. [Ans. 100 mm : 50 mm] 3. A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m. The shear stress in the shaft is limited to 50 MPa. Determine the inside and outside diameters of the shaft, if the ratio of the inside to the outside diameter is 0.4. [Ans. 35 mm ; 90 mm] 4. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmit- ted through a 4 : 1 gearing. 5. A cylindrical shaft made of steel of…
Q1: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The allowable shear stress in the steel is 40 MPa., G70 Gpa (a) What is the required diameter d of the shaft if it is operated at 1500 rpm? (b) What is the required diameter d if it is operated at 3000 rpm? (c) If the length of the shaft from the motor to the gear is 1 m, what are the angles of twist for the two speeds of rotation? Motor GIC G
A shaft is required to transmit 1 MW power at 240 r.p.m. The shaft must not twist more than 1 degree on a length of 15 diameters. If the modulus of rigidity for material of the shaft is 80 GPa, find the MPa] diameter of the shaft and shear stress induced.
1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20 mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42 MPa. [Ans. 152 mm] 2. A shaft 30 mm diameter is transmitting power at a maximum shear stress of 80 MPa. If a pulley is connected to the shaft by means of a key, find the dimensions of the key so that the stress in the key is not to exceed 50 MPa and length of the key is 4 times the width. [Ans. / 126 mm] 3. A steel shaft has a diameter of 25 mm. The shaft rotates at a speed of 600 r.p.m. and transmits 30 kW through a gear. The tensile and yield strength of the material of shaft are 650 MPa and 353 MPa respectively. Taking a factor of safety 3, select a suitable key for the gear. Assume that the key and shaft are made of the same material. [Ans./= 102 mm]
Micro Bh Micros Bb Micros - с * Question Completion Status: Question 2 2.0 d=1.50 in. dia. 1.9 1.8 Class r = 0.08 in. The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when it rotates at 100 rad/s and transmits 5000 lb-in/s. Use CamScanner app or Notes app of iPhone to scan all hand-written pages into one PDF file. Attach the PDF file here to answer in this question. Class ( bbhosted.cuny.edu/webapps/assessment/take/take.jsp?course_assessment_id=_2374 Class D = 2.00 in. dia. r= Fillet radius Class G Cuent Projec suntur Et WA AS hp
3.1.1 If the shaft transmits 150kW, what is the maximum shear stress in the shaft. 3.1 The drive shaft of a truck has outer diameter 60mm and inner diameter 40mm as shown 3.1.2 If the allowable shear stress is 30MPA, what is the maximum power that can be CASI QUESTION 3 below. It is running at 2500rev/min. transmitted? 2500 грm 60 mm 40 mm 60 mm 3.2 A solid circular bar ABC consists of two segments, as shown in the figure. One segment has a diameter of di = 56mm and length of LI diameter of d2 1.45m. The other segment has a 48mm and length L2 = 1.2m. What is the allowable torque Tall if the shear stress is not to exceed 30MPA and the angle of twist between the ends of the bar is not to exceed 1.25°? (Assume G = 80GPA) !! L1
Design a suitable diameter for a circular shaft required to transmit 90 kW at 180 r.p.m. The shear stress in the shaft is not to exceed 70 MPa and the maximum torque exceeds the mean by 40%. Also find the angle of twist in a length of 2 metres. Take C= 90 GPa. [Ans. 80 mm; 2.116°]
Compare the weights of equal lengths of hollow shaft and solid shaft to transmit a given torque for the same maximum shear stress. The material for both the shafts is same and inside diameter is 2/3 of outside diameter in case of hollow shaft. [Ans. 0.56]
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad