1. Compute the area of bronze that will not exceed a stress in bronze of 95 mPa and load P is 81KN. 2. Compute the area of aluminum that will not exceed a stress in bronze of 100 mPa and load P is 106KN. 3. Compute the area of steel that will not exceed a stress in bronze of 150 mPa and load P is 79KN.

1. Compute the area of bronze that will not exceed a stress in bronze of 95 mPa and load P is 81KN. 2. Compute the area of aluminum that will not exceed a stress in bronze of 100 mPa and load P is 106KN. 3. Compute the area of steel that will not exceed a stress in bronze of 150 mPa and load P is 79KN.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tensile force. of 120 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter decreases to 0.01998 m and the length increases to 2.01 m. The true stress on that rod is?
A solid round bar of diameter 250mm has a tensile force of 0.2kN acting on it. What is the stress acting on the bar?
2. A 45-cm long rod of 1020 grade steel will be used as a frame support. It will be subjected to a tension of 50 kN. As a safety factor, design stress is 150 Mpa and rod elongation should be limited to 0.5 mm. Determine the rod's diameter.
1.5 Figure 1.9 shows a circular steel rod of length 40 m and diameter 8 mm, which hangs in a mine shaft and holds an ore bucket of weight 15 kN at its lower end. Calculate the maximum axial stress, taking account of the rod weight, and assuming the weight density of rod to be 77.0 KN/m?. 40 m 8 mm 1.5 kN Figure 1.9
An engineer determines that a 32 cm long rod of 1020 grade steel will be subjected to a tension of 40 kN. The following two design requirements must be met: the stress must remain below 120 MPa, and the rod must stretch less than 0.135 mm. Determine an appropriate value for the rod's diameter to meet these two requirements. (Round up to the nearest millimeter when reporting your answer.) mm
A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to2.01 m. The true axialstrain is?
The femur, the long bone in the thigh, can be modeled as a tube of compact bone for most of its length. The cross-section area of the compact bone in the femur of a 70 kg person is 4.8 x 10-4 m2, a typical value.a. If this person supports his entire weight on one leg, what fraction of the tensile strength of the bone does this stress represent?b. By what fraction of its length does the femur shorten?
4. A ring made of 2.5 cm diameter steel bar carries a pull of 10 kN. Calculate the maximum tensile and compressive stresses in the material of the ring. The mean radius of the ring in 15 cm.
TOPIC: ELASTICITY A load of 50 kg is applied to the lower end of a steel rod 80 cm long and 0.60 cm indiameter. How much will the rod stretch? Y = 190 GPa for steel. Please help me solve this problem with complete solution and box the final answer. Please also draw an illustration based from the given. Thank you!
Thank you!! Calculate the maximum tensile stress in a plate subjected to a remote loading of P. The plate has a central hole as shown below. The stress concentration at the hole is 2.5 based on the remote average stress. The Plate thickness is 1cm, plate width 20 cm and the total load P is 25 kN. Identify the location of the maximum stress at B
The cross sectional area of the bar is 5cm^2 What is the stress in steel?
Kindly solve this problem with complete solution so that I can Understand. Correct Final answer: 1400 or 1.4x10^3