1. Determine the minimum coefficient of static friction us which will allow the drum with fixed inner hub to be rolled up the 17° incline at a steady speed without slipping. What are the corresponding values of the force P and the friction force F? 17

1. Determine the minimum coefficient of static friction us which will allow the drum with fixed inner hub to be rolled up the 17° incline at a steady speed without slipping. What are the corresponding values of the force P and the friction force F? 17

Name: 1. Determine the minimum coefficient of static friction us which will
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 1. Determine the minimum coefficient of static friction us which will allow the drum withfixed inner hub to be rolled up the 17° incline at a steady speed without slipping. Whatare the corresponding values of the force P and the friction force F?17

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.36P: The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find...

See similar textbooks

Similar questions

A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The sling with a sliding hook is used to hoist a homogeneous drum. If the static coefficient of friction between the cable and the eye of the hook is 0.6, determine the smallest possible value for the angle 6.
The square-threaded screw of the C-clamp has a mean diameter of 9 mm and a pitch of 1.5 mm. The coefficient of static friction between the threads is 0.2. If the torque M = 1.25 N · m is used to tighten the clamp, calculate (a) the clamping force; and (b) the torque required to loosen the clamp.
Determine the minimum coefficient of static friction ???? which will allow the drum with fixed inner hub to be rolled up the 15o incline at a steady speed without slipping. What are the corresponding values of the force P and the friction force F? Use a mass of 50 kg and a radius r= 0.5 m.
The two uniform slender bars constructed from the same stock material are freely pinned together at B. Determine the minimum angle 0 at which slipping does not occur at either contact point A or C. The coefficient of static friction at both A and C is u, = 0.50. Consider only motion in the vertical plane shown. B
Calculate the horizontal force P on the light 15° wedge necessary to initiate movement of the 59-kg cylinder. The coefficient of static friction for both pairs of contacting surfaces is 0.39. Also determine the friction force Fg at point B. (Caution: Check carefully your assumption of where slipping occurs.) Answers: P= i 596 FB=366 59 kg B N N
Calculate the horizontal force P on the light 14° wedge necessary to initiate movement of the 49-kg cylinder. The coefficient of static friction for both pairs of contacting surfaces is 0.40. Also determine the friction force FB at point B. (Caution: Check carefully your assumption of where slipping occurs.) P Answers: P = FB = i i 4.87e+2 3.09e+2 49 kg B N A N
A flat belt passes over two idler pulleys and under a rotating drumof diameter 8 in. The axle of the drum is free to move vertically ina slot, and a spring keeps the drum in contact with the belt. Whatis the minimum force which should be exerted by the spring if slippageis not to occur when a 30-lb · ft torque is applied to the drum? Thecoefficient of static friction between belt and drum is 0.30 and theangle of contact is 180 degrees.