1. Disk A is constant thickness and is at rest when it is placed in contact with belt BC, which moves with a constant velocity v. Denoting mk the coefficient of kinetic friction between the disk and the belt, derive an expression for the number of revolutions executed by the disk before it attains a constant angular velocity. A C B

1. Disk A is constant thickness and is at rest when it is placed in contact with belt BC, which moves with a constant velocity v. Denoting mk the coefficient of kinetic friction between the disk and the belt, derive an expression for the number of revolutions executed by the disk before it attains a constant angular velocity. A C B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6/47 A block of mass mo is placed between the vertical wall and the upper end A of the uniform slender bar of mass m. If the coefficient of static friction is µg be- tween the block and the wall and also between the block and the bar, determine a general expression for the minimum value 0min Oof the angle 0 for which the block will remain in equilibrium. Evaluate your expression for the conditions µ = 0.5 and %3D т (a) mo 0.1, m (b) mo 1, and m (c) mo 10. %3D For each case, state the minimum coefficient of sta- tic friction (u)B necessary to prevent slippage at B. Ans. (a) 0min = 61.2°, (µ,)B = 1.667 (unusual!) (b) 0min = 45°, (µ)B = 0.667 (c) 0min = 10.30°, (µ,)B = 0.0952 %3D %3D %3D %3D %3D mo m (Ha)B Problem 6/47
5. End A of the 6kg uniform rod AB rests on the inclined surface, while end B is attached to collar of negligible mass which can slide along the vertical rod shown. Knowing that the rod is released from rest when ? = 35° and neglecting the effect of friction, determine immediately after release (e) The angular acceleration of the rod, (f) The reaction at B.
SITUATION 3. The spring-mounted slider moves in the horizontal guide with negligible friction and has a velocity voin the s-direction as it crosses the mid-position where s = 0 and t= 0. The two springs together exert a retarding force to the motion of the slider, which gives it an acceleration proportional to the displacement but oppositely directed and equal to a = −k²s, where k is constant. (The constant is arbitrarily squared for later convenience in the form of the expressions.) Determine the expressions for the displacements and velocity v as function of the time t.
The 2.5-kg collar is at rest in position A when the constant force Pis applied as shown. Determine the speed of the collar as it passes position B if P = 45 N. The curved rod lies in a vertical plane, and friction is negligible. F1.5 m 42° B 3.0 m 42 Part 1 How much work Upis done by the force P = 45 N on the collar? Answer: Up = i N-m
The block of weight W2 is being held in its position by two cylindrical rollers resting on inclinedsurfaces. All contact surfaces have a coefficient of static friction, us = 0.36. W1 = 400KN. a. What maximum value of W2 it can be before slipping of the block happens?b. Determine the normal force reaction against the inclined surfaces.
5. The uniform rod has a mass of 10 kg and rests on the inside of the smooth ring at B and on the ground at A. If the rod is on the verge of slipping, determine the coefficient of static friction between the rod and the ground. B 0.5 m 0.2 m 30° A
Problem 2: The 2-kg collar is released from rest at A and slides down the inclined fixed rod in the vertical plane. The coefficient of kinetic friction is 0.4. Calculate (a) the velocity v of the collar as it strikes the spring and (b) the maximum deflection x of the spring. 2 kg 0.5 m 4 H₂ = 0.4 60° WWWWW k = 1.6 kN/m
Give me right solution. A closed cylindrical tank 30 cm in diameter and 120 cm high contains 90 cm of liquid SL = 0.80). The rest is air under a pressure of 12 kPag. The above tank is rotated about its geometric axis at the center a rate of 200 RPM. At the above angular speed: Determine the following (a). force on the inside top of the tank in kN. (b) force on the inside bottom of the tank in kN
At the instant θ = 30 degrees, the 10 Kg slender bar of length L =0.9 m has a clockwise angular velocity of 2.5 rad/s. The coefficient of kinetic friction at end B is 0.22; end A is attached to a massless roller that rolls on the smooth horizontal plane. Answer the following, 1) find the angular acceleration 2) Reaction forced at A and B 3) horizontal and vertical components of acceleration of the rod's center of mass
5. The 4-N weight slides with negligible friction on a horizontal table. The spring attached to the weight has a stiffness of 20 N/m and a free length of 0.5 m. When the weight is at A, its velocity is 10 m/s directed as shown. Determine the speed of the weight at B where the length of the spring is 0.8 m. Also, find the rate at which the spring is elongating at B. Horizontal table 0.8 m L 0.6 m A 4 N 10 m/s B
1. A 6 kg slider is released from rest at Point A and slides with negligible friction in a vertical plane along the circular rodshown below. The attached springhas a stiffnessof 520 N/m and an unstretchedlength of 0.6 m.a. Determine the change in potential energy when the slider is at B in joules. b.Determine the change in elastic potential energy when the slider is at B in joules c. Determine the velocity of the slider at B in meters per second.
Body A has a mass of 25 kg and body B has a mass of50 kg. The coefficient of friction for all surfaces is0.20. Find the minimum force P that can be appliedto B without disturbing the equilibrium of thesystem.