Discussion: 1. Does plane section (square plane) on the surface of the circular shaft remain plane after loading for the shaft under torsion (compare between elastic and plastic deformation)? Justify your answer by drawing vertical and horizontal lines over the shaft length. 2. How is shear modulus related to Young's modulus? 3. Does the distance from the cross section neutral-axis effects the calculated shear stress? How? 4. Solid and hollow aluminum shaft with same outer diameter, which will twist more? Why?

Discussion: 1. Does plane section (square plane) on the surface of the circular shaft remain plane after loading for the shaft under torsion (compare between elastic and plastic deformation)? Justify your answer by drawing vertical and horizontal lines over the shaft length. 2. How is shear modulus related to Young's modulus? 3. Does the distance from the cross section neutral-axis effects the calculated shear stress? How? 4. Solid and hollow aluminum shaft with same outer diameter, which will twist more? Why?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
y 400 mm 4 mm B 200 mm A 6 mm The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear stress in the plate if the shear modulus of the material is 2 MPa. Express your answer in kPa and round it to the nearest integer if necessary.
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
The plastic distorts as shown by the dashed lines. (Figure 1) The dimensions are L= 460 mm H =310 mm di =2 mm, d2 =5 mm, dz = 15 mm, d4 =8 mm, d; =2 mm, and de = 5 mm. Part A Determine the shear strain Yry at corner C. Express your answer to three significant figures and include appropriate units. (yc)zy = Value Units igure Submit Request Answer dz Part B B Determine the shear strain yzy at corner D. Express your answer to three significant figures and include appropriate units. H HA ? D Value Units
A test conducted on a steel bar whose cross section is 0.5 in. by 4 in. is performed. Anaxial load of P = 30,500 lb. produced a deformation of 0.00103 in. over a gauge lengthof 2 in. and a decrease of 0.000078 in. in the 0.5-in. thickness of the bar. Determinea. Poisson’s ratio,b. the elastic modulusc. the decrease in the 4-in. cross-sectional dimension.
Given: A steel rod (A = 150mm^2) is stretched between two fixed points with a tensile load of 5000N at 20degree C. determine: a) the stress at -20 degree C b) at what temperature will the stress be zero *DRAW THE FBD: COMPLETE SOLUTION *USE 3 DEC PLACES
ProbleT = - An aluminum bar has diameter d = 40 mm, shear modulus of elasticity G = 27 GPa, and torque T = 300 N.m. (a) Determine the maximum shear, tensile, and compressive stresses in the bar, and show these stresses on sketches of properly oriented stress elements. (b) Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements. |d=40 mm T= 300 N-m
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47
A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm) diameter. Determine the followings: 1- The stresses in each material when a compressive force of 70 kN is applied on the compound bar and the temperature is changed from 20 °C to 40 °C. 2- The compound modulus of elasticity (Ec). Knowing that : E=200GN/m² E=70 GN/m² and a=11×10% per °C and a=22×10 per °C for Steel for Aluminum Alloy
A line is inscribed on a 3 mm thick steel alloy plate with an elastic modulus E = 200 GPa and shear modulus G = 70 GPa. The plate is then loaded as shown below. 2a) Determine the slope of the line after the plate has been loaded 2b) Determine the reduction in thickness of the plate (in mm) under the applied loads 2c) If the plate has a yield stress = 300 MPa, determine the factor of safety against failure according to the Maximum Normal Strain (St. Venant's) Criterion Steel Alloy Plate: y line 250 mm k Į 50 kN 70 mm ↑ 70 mm 100 KN 125 mm