1. For each state of plane stress shown below, i.e., for configurations (a) and (b), indicate whether each component of the state of strain is: = 0 (equal to zero) >0 (greater than zero) <0 (less than zero) The material is linear elastic with Possion's ratio is between (0, 0.5), and the deformations are small. T 30 e X 0 Ex Ey Ez Yxy Yyz Yzx (a) (b) 1° (b) 1x

1. For each state of plane stress shown below, i.e., for configurations (a) and (b), indicate whether each component of the state of strain is: = 0 (equal to zero) >0 (greater than zero) <0 (less than zero) The material is linear elastic with Possion's ratio is between (0, 0.5), and the deformations are small. T 30 e X 0 Ex Ey Ez Yxy Yyz Yzx (a) (b) 1° (b) 1x

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Similar questions

Q- Principal stress at a point in an elastic material are 1.5 o (tensile), o (tensile) and 0.5o (compressive). The elastic limit in tension is 210 MPa and μ = 0.3. Find the value of o at failure when computed by maximum principal strain theory.
AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS ARE APPLIED AT THE POSITIONS INDICATED. FIND THE VALUE OF P THAT WILL NOT EXCEED A MAXIMUM OVERALL DEFORMATION OF 5mm OR A STRESS IN THE STEEL OF 120MPa, IN BRONZE OF 130 MPa AND IN ALUMINUM OF 90 MPa. Modulus of Elasticty of Bronze = 80 GPa, Aluminum = 65 GPa and Steel = 210 GPa. 2P P 3P 4P L = 500mm 800 A = 400mm² 900 600 700 C
A 3m long steel plate having a cross section of 25mm by 300mm is use as a hanger and subjectedto a tensile load of 1070 kN. The proportional limit of the steel is assumed to be 200 MPa. If thePoisson’s ratio is 0.25, determine the following;a. The transverse strain,b. The total axial deformation, andc. The transverse dimensional change along 300mm.
Question- Principal stress at a point in an elastic material are 1.50 (tensile), o (tensile) and 0.50 (compressive). The elastic limit in tension is 210 MPa and poisson's ratio=0.3. Find the value of o at the failure when computed by the maximum principal strain theory.
An element in plane stress is subjected to stresses o, = -8400 psi, ay = 1100 psi, and ty = 1700 psi (see figure). The material is aluminum with %3D modulus of elasticity E =10,000 ksi and Poisson's ratio v = 0.33. Determine the following quantities: (a) the strains for an element oriented at an angle 30 degrees, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements. Ty Txy Ox
A plate in equilibrium is subjected to uniform stresses along its edges with magnitude o = 30 %3D MPa and ow = 50 MPa as shown in the figure. %3D = 50 MPa %3D O = 30 MPa XX ple The Young's modulus of the material is 2 x 1011 N/m2 and the Poisson's ratio is 0.3. If o is negligibly small and assumed to be zero, then the strain Ezz is
For a given steel cube section subjected to three dimensional state of principal stress. 75N/mm² ŠI 150 N/mm 30 N/mm² Consider yield stress = 250 N/mm², and µ = 0.3 The value of factor of safety according to maximum strain energy theory. -X
Steel Stress-Strain diagram. Which of the following statements is NOT correct? Engineering stress is the stress computed using the original area and not the necking down area. The constant stress region is called the yield plateau or plastic range. The linear portion is also called the plastic range. The proportional limit, elastic limit, upper and lower yield points are very close to one another and are treated as a single point called the yield point.
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 660 mm. The cross-sectional dimensions of the beam are b1 = 31 mm, d1 = 117 mm, b2 = 19 mm, d2 = 19 mm, and a = 6 mm. For this material, the allowable tensile bending stress is 14 MPa, and the allowable compressive bending stress is 9 MPa. Determine the largest moment M that can be applied as shown to the beam.
In terms of oxx , O yy and the material properties having a plane strain state; write the expression of the o zz Assuming there is no z-shear strain?
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MPа. Aluminum A = 400 mm? Bronze A = 200 mm Steel A = 500 mm? 2P 4D 2.5 m 2.0 m 1.5 m
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 840 mm. The cross-sectional dimensions of the beam are b1 = 30 mm, d1 = 108 mm, b2 = 18 mm, d2 = 18 mm, and a = 6 mm. For this material, the allowable tensile bending stress is 17 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M. d2 d1 | A В