1. Given the connection shown below carrying a load P = The connection consists of four pieces 20mm x 200mm x 700mm steel blocks fastened by four pieces 12mm diameter rivets. Solve a. Maximum shearing stress (2 decimals in MPa) b. Maximum tensile stress (2 decimals in MPa) c. Maximum bearing stress (2 decimals in MPa) Top View 700mm 100mm 100mm P 200mm Side View

Q: The axial load 210 kN applied to the lap joint is distributed equally among the three 16.5-mm-…

A:

Q: 2. A lap joint is fastened by three 20mm diameter rivets and carries a load of 50 KN as shown.…

A: Width of plate(w)=150mm Thickness of plate(t)=25mm Diameter of river(d)=20mm Number of rivet(n)=3

Q: The solid aluminum shaft ABCD carries the three torques shown. (a) Determine the smallest safe…

A: Given: The allowable shear stress is 30 ksi. The shear modulus G is 4 x 106 psi. Consider the…

Q: 4. Calculate the principal stresses at points A and B for the bracket shown. The bracket is lin…

A:

Q: Three cables having an area of 0.05 in? each is carrying the load W as shown. With no stress, the…

A: Given, A = 0.05 in2  E = 29000 ksi

Q: find the inside diameter of the pipe

A: Internal Diameter = 59.61 mm

Q: Knowing that the bracket AB has a uniform thickness of t, Base of theory of elasticity, determine…

A: Given,

Q: In the bolted connection as shown in the figure, assuming that the applied load is uniformly…

A:

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

A:

Q: 3. Determine the length of the 2-mm diameter bronze wire which can be twisted through two complete…

A:

Q: A connection using 3 bolts with the eccentricity is shown in Figure Q3. Determine: (a) Average shear…

A:

Q: A screw is rotated as shown to provide tension on a cable that passess over a frictionless pulley…

A: The given figure is shown below:

Q: The bracket show in the figure is bolted with 5-20mm dia. Bolts. It carries an eccentric load of…

A: Given data, 5-20mm diameter bolts Eccentric load of P= 35KN

Q: (load) Trsmm |00 mm חחףך 125 mm F (load) 150 mm

A: I have determined the value of load P and mentioned complete calculation.

Q: Knowing that the bracket AB has a uniform thickness of t, Base of theory of elasticity, determine…

A:

Q: 1. The compound shaft shown in the figure is attached to rigid supports. For the bronze segment AB,…

A: It is given that :

Q: Compute the Principal stresses and max shearing stress and their direction at Point (A) shown in…

A:

Q: Problem # 3: The strut AB made from two bars (thickness of each bar = 0.50 in) is connected to a…

A:

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

A:

Q: (i) Diameter of the steel bar (ii) Gauge length of the bar = 3 cm = 20 cm (iii) Load at elastic…

A:

Q: Prob. 6 * The pipe wrench is parallel to the z-axis, and is subjected to a 40lbf force in the -y…

A:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A:

Q: P 100 mm 10 mm 10 mm P

A: As per bartleby guidelines the given data closely related to the IS code provisions also the term…

Q: . Calculate "P" in KN considering tension failure on gross area b. Calculate "P" in KN considering…

A: since the given question has multi part. therefore, only 1-3 will be solved.

Q: 4. Six rivets are used in the connection shown in the figure. If both P = 50 kN, what is the minimum…

A: Load P = 50KN Allowable shear stress = 70MPa Bearing stress = 40MPa

Q: Determine the bolt diameter if the shear stress is 150 MPa and the bearing stress is 337.50 MPa.

A: The values and diagram given in the question are as follows: Shear stress(t)=150 MPa Bearing…

Q: 3. A 16 mm steel bar AB and a 25 mm steel bar BC support a load P = 7,500 N as shown. If E= 200 GPa,…

A:

Q: Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: Calculate the value of P using both shear stress criteria and angle of twist criteria. The criteria…

Q: The yoke-and-rod connection shown is subjected to a tensile force of 5 kN. Determine the average…

A:

Q: Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1= 50, y2 = y3…

A:

Q: From the given figure: W = 2.4 KN L2 = 1.2 m L1 = 1.2 m L3 = 1.2 m BC is 75 mm wide x 10 mm thick…

A:

Q: Refer to Fig. 3-37. A flat plate hinged at C has a configuration satisfying the equation x² + 1.5y =…

A: Consider the free body diagram;

Q: 7. The bracket shown is welded on one side of a steel column with 800mm of 6mm fillet weld.…

A: Given data P = 44 KN  Size of weld (S) = 6mm  Length of weld = 800mm  Due to symmetrical welding…

Q: A wide flange A60 steel column has a length of 6.4meters and pinned ends. If Sx=888x103 mm3,…

A: The given column has pinned ends hence the actual length 6.4m is the unsupported length, l = 6400mm…

Q: Determine the magnitude of the pin force at A. Assume W = 810 lb, a = 3.7 ft, b = 2.5 ft, r = 7 in.…

A:

Q: 12 in. 9 in. B 40 lb The pipe wrench is parallel to the z-axis, and is subjected to a 40lbf force in…

A:

Q: 1. For the connection shown in the figure below, determine the shearing stress in the most heavily…

A: In designing practice it isn't unexpected needed that two sheets or plates are combined and convey…

Q: Two overlapping plates are joined by a 0.75-in diameter pin. If the shear force on the pin is…

A:

Q: The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute…

A: Given data The plate is fastened to the fix member by three 10 mm diameter rivets

Q: 1. Given the connection shown below carrying a load P = The connection consists of four pieces 20mm…

A:

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

A:

Q: A 2500 Ib horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are…

A: Answer:-                 In this question we will use equation of equilibrium and condition of…

Q: W = L2 = %3D 2.4 1.2 KN m L3=1.2 L1 = L3 1.2 1.2 Typical connection at all joints. m Im Li=1.2…

A:

Q: QUIZ 1 Five rivets holds three sheets of steel together, and is loaded as shown below. If the…

A:

Q: Pin diameter = 10 mm Gusset plate 15 kN Pin 50 mm Steel plate 6 mm thickness Column For the pin…

A: Given data: P=15 x 103  b=50 mm t=6 mm d=10 mm

Q: The lap joint shown in figure is fastened by four 1-in.-diameter rivets. (a) Calculate the minimum…

A:

Q: Knowing that the bracket AB has a uniform thickness of t, Base of theory of elasticity, determine…

A: Given A bracket having uniform thickness t Required Maximum principle stress

Q: The shaft is made of two segments. AC has a diameter of 0.5in, and CB has a diameter of 1in. It is…

A: Find the minimum shear stress in the shaft as follows:Let the torque at end A be TA and the torque…

Q: A flanged-bolt coupling consisting of six % inch diameter steel bolts evenly spaced around a bolt…

A:

Q: Q3/ The lap joint shown in figure below is fastened by four 19 mm diameter rivets. Calculate the…

A: Types of welding joints: There are four types of welding joints. They are 1) lap joint 2) Butt joint…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.