1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steeldrill. At what speed in revolutions per minute should he operate the drill press?2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece usinga high carbon steel drill.3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of ahigh speed drill if it is used to drill a tool steel material?4. A drill press has the following rpm settings; 350, 600, 1100, & 1600. What rpm setting must beused if a 15 mm high speed steel drill is used to cut brass workpiece?5.A machine operator drills a hole of a 3/8 inch diameter to a stainless steel using a carbon steeldrill. He sets the drill press rpm setting to 900 rpm. Is he operating at correct setting? If not,then what must be the correct rpm setting considering that the machine has the following rpmsettings of 300, 600, 900, 1200, and 1800?

Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three questions.…

1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel drill. At what speed in revolutions per minute should he operate the drill press? 2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece using a high carbon steel drill. 3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of a high speed drill if it is used to drill a tool steel material?

1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel drill. At what speed in revolutions per minute should he operate the drill press? 2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece using a high carbon steel drill. 3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of a high speed drill if it is used to drill a tool steel material?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. What type of milling machine can be used to make the groove in the shaft?2. The diameter of the shaft is d = 25 mm. Find the width and depth of the groove (use the table below).3. Find the diameter of the tool.4. Find the speed of rotation (RPM N) of the tool during roughing and finishing.The material of the shaft is Stainless Steel (C45) with CARBIDE TOOL.
What is the cutting speed of turning in the unit of m/min, when main axis spindle speed is 2,409 rpm and external diameter is 86mm ? Answer in 2 decimal points. Calculate the theoretical spindle rotational speed in rpm required to drill a 1 mm hole in copper using high speed steel drill. The recommende cutting speed is as following. The thickness of the copper plate is 24. (Leave the answer in numerical value, no need to key in 'rpm') Typical cutting speeds (m/min) High speed steel Material Tungsten carbide Aluminum 100 500 60 330 Copper Hard brass 45 230 Bronze 35 180 Mild steel 28 250 Cast iron 20 160
A steel cylinder 5 inch in diameter is to be machined in a lathe. If the desired linear velocity of the cylinder's surface is to be 2.3 ft/sec. At how many revolutions per minute should it rotate? 122.67 rpm 105.14 rpm 112.28 rpm O 114.06 rpm
Find the commercial tap drill size for 1⁄2”-20 NF bolt.
QUESTION 5 Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning a 1º diameter copper rod with a depth of cut of 0.1" using a cemented carbide tool. O N=287 RPM, F-25.8 in/min, P=9.7 hp ON=2866 RPM, F=258 in/min, P=97 hp ON=1146 RPM, F-25.8 in/min, P=97 hp O N= 11460 RPM, F-340 in/min, P=130 hp ON= 1146 RPM, F-34 inimin, P= 13 hp ON= 115 RPM, F-3.4 in/min, P=1.3 hp QUESTION 6 It is required to face mill an aluminum block to size it down from 2" to 1.5" thick using a 3" diameter 2-toothed carbide cutting tool. The block is 6.0" wide and 6" long. The entire tool diameter engages the workpiece during the cut. Calculate the recommended spindle speed in revolutions per minute, feed per tooth, and cutting power required. O N=1529 RPM, f= 0.026 in/rev/tooth, P = 36 hp O N-3820 RPM, f= 26 in/revitooth, P=27 hp O N-3820 RPM, f= 0.052 in/rew/tooth, P=27 hp ON-382 RPM, F= 0.026 in/revitooth, P = 0.027 hp O N-3820 RPM, f= 0.052 in/rev/tooth, P=2.7 hp…
1. List the operations and the tools needed to make the following shape.2. Find the speed of rotation (RPM N) of each tool during roughing andfinishing.The material of the piece is Stainless Steel (C45) with CARBIDE TOOL.
In milling operation, the cutting speed is 150 m/min with a tool of 12 mm diameter. What is the right spindle speed rpm for this operation? (Choose the most close to your calculated value) 4500 O 3980 3700 4200
Please solve it correctly , Don't Use Ai tool. (1) A twist drill bit is used to drill a hole of diameter 2.0 at 4578.1 rpm at a feed rate of 2.5 in/min. Calculate the MRR in in^3/min. Take "pi" = 3.14. Round your answer to the nearest tenth.
Write the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS drill bit and T2 is a 0.5" tapping bit. The rest of the features are cut using a 0.75" HSS milling tool, T3. Feed rate and spindle speed are 10 ipm and 2000 rpm. The material is low- carbon steel. Part thickness is 0.5”. Use dotted lines two show the path of tools movements. Set up proper operation conditions as discussed in the class today.
A high-speed heavy duty plain milling cutter 4 inches in diameter with 12 teeth is to be used. Each tooth s expected to remove 0.006 inch. What is the feed per revolution? 2. The feed per revolution is 0.0072 inch/rev and the machine is set for 120 rev/min. Find the feed in inch per minute
To facilitate the milling (roughing) work of a cast steel material using a 1.5 inch diameter cutter choose between the two available stock. Find the speed of the cutter in rpm. – high speed steel cutter with a cutting speed of 50 fpm or – carbide tipped cutter with a cutting speed of 200 fpm.
plz give a full explained answer ASAP within 30-40 min upvotes will be given.