1. If the potentiometer in the below figure is adjusted from a setting near the bottom (low resistance from wiper to ground) to a setting near the top (higher resistance from wiper to ground), the average current through will (a) increase (b) decrease (c) not change 2. If the diode in the below figure opens, the voltage across will (a) increase (b) decrease (c) not change

1. If the potentiometer in the below figure is adjusted from a setting near the bottom (low resistance from wiper to ground) to a setting near the top (higher resistance from wiper to ground), the average current through will (a) increase (b) decrease (c) not change 2. If the diode in the below figure opens, the voltage across will (a) increase (b) decrease (c) not change

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Question-1: Consider the circuit in Figure below. 1. What type of circuit is this? 2. What is the total peak secondary voltage? B. Find the peak voltage across each half of the secondary. 4. Sketch the output voltage waveform across R1. 5. Sketch the voltage through D1? 6. What is the PIV for each diode? 120 V rms D2
Draw vx and v0 according to the input voltages in the circuit shown in the figure. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, the threshold voltages of diodes will be VE = 0.7V.
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp=20V, V1=5 V and V2=9 V. R DZ D1 Vin Vout v2 Maximum voltage of output waveform Minimum voltage of output waveform
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
Figure 2 shows a circuit for charging a 12 v battery. If Vs is a sinusoidal input with 30 v peak amplitude, determine: i. The fraction of each cycle during which the diode conducts. ii. The peak value of the diode current iii. The maximum reverse bias voltage that appears across the di ode. 100 n 12 V Figure 2
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=3 V and V2=8 V. R www D2 DI Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform
In the circuit shown in the figure, draw vx and v0 with a scale according to the input voltages. note = R1 = 10Kohm R2 = 1kohm R3 = 1Kohm, threshold voltages of diodes shall be VE = 0.7V.
Q1. For the circuit shown in Figure below find the maximum and minimum values of zener diode current. 5 k2 80 – 120 V 50 V 10 kN
Q1/ +5 V +50 V V R. Vin R 47 N 3.3 kN -5 V -50 V (a) (b) a. Draw the output voltage waveform for each circuit in above figure and include the voltage values. b. What is the peak inverse voltage across each diode? c. What is the peak forward current through each diode?