1. Let us suppose a 15-minute count of vehicles bound for Malolos City was conducted at a particular location on McArthur Highway. A summary is shown in the table below: TYPE 10-MINUTE COUNT Car/van 300 Jeepney 30 Bus 10 Truck 35 Estimate the flow rate in vehicles per hour.

1. Let us suppose a 15-minute count of vehicles bound for Malolos City was conducted at a particular location on McArthur Highway. A summary is shown in the table below: TYPE 10-MINUTE COUNT Car/van 300 Jeepney 30 Bus 10 Truck 35 Estimate the flow rate in vehicles per hour.

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter6: Fundamental Principles Of Traffic Flow

Section: Chapter Questions

Problem 26P: The arrival times of vehicles at the ticket gate of a sports stadium may be assumed to bePoisson...

See similar textbooks

Related questions

Q: What do you understand the building ordinance?

A: Explanation- The buildings ordinance is a set of restrictions adopted by state or municipal…

Q: 15-17. If the W 360x45 beam is made from steel having an allowable normal stress of allow = 150 MPa…

Q: 1. Hydrostatic force on a curved surface Consider the container with the half-sphere dome, filled…

A: radius of sphere R = 1 m Height = 10 m

Q: A tank contains 13 kg of CO₂ at 20°C and 1.96 MPa. Take R = 189 m2/(s2 .K). Estimate the volume of…

A: Use ideal gas equation in terms of Volume V V = mRT / P where, m = 13 kg R = 189 T = 20 C = 293…

Q: Determine the required Magnitude and location from point B of the resultant of the Forces acting on…

A: Answer Let us first draw the forces acting on the dam body as shown below As nothing is given about…

Q: mo

Q: From the table, compute the absorption capacity (%) of sample II. From the table above, which of the…

A: Given Data:weight of saturated surface Dried sample= 2490Weight of Even dried = 2384

Q: B C E 2 m 2m 2 m b) Determine the force in member DE c) Determine the force in member CD 4 m D 500 N…

Q: 1. Most employers do not check a new employee hearing to establish their hearing level. - 2. Where…

A: This question is from environmental and safety engineering This question some basics statement is…

Q: Q1) Determine the reactions at all supports in the beam shown. The support at A is displaced…

A: Given a continuous beam having support A settled by 100mm (0.1 m) EI = 200*5 KN-m² Required…

Q: For the beam loaded as shown in figure, a) calculate the slope of the elastic curve over the right…

A: Given: A beam Required : a) calculate the slope of the elastic curve over the right support b)…

Q: A spherical tank has an inside diameter of 3.85 m. The tank is to contain gas at an internal…

Q: 2. Which of the following gives the moment about point C of force TAD acting at A? (-180i - 240j +…

Q: Q3. Discuss the importance of reinforcing the concrete?

A: To find : The importance of reinforcing concrete

Q: Using the area method, draw the shear force and bending moment diagrams for the beam. Don't think…

A: Given A simply supported beam Required Shear and bending moment diagram using area method

Q: Which of the following gives the axial and shear force at point A on the beam, respectively? (kN)…

A: Consider the figure,

Q: A building is fetching an annual rent of Rs. 1,80,000/-. The purchaser desires to get 5% return on…

Q: 6 ft B 10 kips/ft 9 ft 5 ft D

A: Determine Support Reactions: Take moment @ A, VD×20=10×9×10.5 VD=47.25 VA=42.75 As per rule of…

Q: The frame is loaded as shown. Using Moment Distribution Method, determine the support reaction.…

Q: A drainage canal in the shape of trapezoid with a bottom width of 2,3m and a side slope of 1…

Q: What will be the factor of safety against seepage if cohesion is 19 kPa, angle of backfill is 32…

A: Given Cohesion = 19 kpa Angle of backfill = 32 degree

Q: 30 kN 4 kN/m I B EI 2EI ΕΙ 4 m 8 m -12 m 10 m MOMENT DISTRIBUTION METHOD. Solve the member…

A: Solve Internal moment at support using Moment Distribution Method

Q: Q2): 1200 BPD of 32. were obtained in the Volu Perc Gasoline 26.8 Naphtha 5.63 Kerosene 19.8 Gas oil…

A: Given :

Q: Help Save & The Stokes-Oseen formula for drag force Fon a sphere of diameter D in a fluid stream of…

Q: 7. A water treatment plant of 200 m³/ day uses an activated carbon, in columns, to reduce phenol…

A: Given, V = 200 m3/day or 200000 L/day Co = 130 mg/L Ce = 10 mg/L

Q: 5.2kN-m 20 KN 2.5 in. 75KN Fig. 6a Fig. 7 7. The thin rectangular plate shown in Fig. 7 is uniformly…

Q: A manufacturing company wants to produce a closed right cylindrical can that will hold 2.5 L of…

Q: Sedimentation in dams remains a cause for concern which affects dam stability and ultimately…

A: INTRODUCTION Sedimentation is a natural process in all water bodies which is relatively higher in…

Q: A water tower supplies water through the plumbing in a house. A 3.28-cm-diameter faucet in the house…

Q: A 6 ft B 10 kips/ft 9 ft 5 ft D X

A: Given data:- Below diagram is giving in question;

Q: Problem 4:a) Determine the stresses ox, oy, and Txy, and show them on a stress element. (b)…

Q: An wants Engineer to convert a tied rectangular column to a spiral column having H=500mm and…

Q: Three pipes are connected in parallel. The difference in heads in each pipe is 40 m. Pipes Diameter…

Q: 15-17. If the W 360x45 beam is made from steel having an allowable normal stress of allow = 150 MPa…

A: It is given that :

Q: Determine the absolute weight and the weight relative to the rotating earth of a 100-kg man if he is…

Q: Determine the reactions for the shown structure. P1=2kN, P2=4kN E 30° B D 30° C

Q: A simply supported beam with length of 5 Meters is loaded with a counterclockwise couple of 5 KN.M…

A: Simply supported beam is a determinate structure with one end hinged and other end roller supported.…

Q: A drainage canal in the shape of trapezoid with a bottom width of 2.3m and a side slope of 1…

Q: 21. Classify the following soil according to USCS. Please present your steps logically Sieve %…

A: Percentage Passing through 4.75 mm sieve ie No.4 sieve = 90% > 50% Hence the Sample is a sand…

Q: Question 1 Given the frame in Figure 1 below. Do the following: 1.1 Calculate the reactions at A and…

A: Use moment distribution method , Determine stiffness of each member, KAD = 3EIL=3EI4 KGE =…

Q: wharves along and parallel to the shore

A: Given Line: wharves along and parallel to the shore is known as Jetties.

Q: A is effect on runway........... length Type of service Community size O Humidity O

Q: Determine the stresses ox, oy, and Txy, and show them on a stress element. (b) Determine the…

Q: B. Determine the support reactions at A, C & D of the loaded beam.... 150 KN 45KN/m B 3.0 m 1.50 m…

A: Let's draw the FBD for better understanding

Q: 3. During heavy traffic congestion, it was observed that the average spacing of vehicles in queue in…

Q: For the beam and loading shown, determine the shear and moment as functions of position, and choose…

A: The length of beam, L=6ft The magnitude of triangular load =336lb/ft

Q: 4. A parallel reversed curve has an equal radius of 360m and a central angle of 8°. a. Compute the…

Q: Problem (9.5): Determine the radius of the round strut so that the round and square struts shown in…

A: The given data is: E=200 GPa=200*103 mpa=200*103 N/mm2 Circular strut, L=1 m Square strut length,…

Q: A W 5 m B -2.5 m- : C

Q: Determine the flow in pipe 3.

A: Parallel connection: - It is defined as the connection where a pipe divides into two or more pipes…

Concept explainers

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.

Question

1. Let us suppose a 15-minute count of vehicles bound for Malolos City was conducted at a
particular location on McArthur Highway. A summary is shown in the table below:
TYPE 10 MINUTE COUNT
Car/van 300
Jeepney 30
Bus 10
Truck 35
Estimate the flow rate in vehicles per hour.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The arrival rate at a parking lot is 6 veh/ min. Vehicles start arriving at 6:00 P. M., and when the queue reaches 36 vehicles, service begins. If company policy is that total vehicle delay should be equal to 540 veh-min, what is the service rate? (Assume D/ D/ 1 queuing and a constant service rate.)
Choose the right answer traffic volume data has been collected for 15 min time intervals as shownbelow. Find the total hourly volume, flow rate and peak hour factor (PHF). Time:7:30 - 7:45 7:45 - 8:00 8:00 - 8:15 8:15 - 8:30 Volume 200 300 350 250 * a-0.876 b-0.877 c-0.878
The following table shows 5 – min vehicle counts that have been recorded for a given transportation facility during A.M. peak hour: a.) Determine the maximum flow rate (veh/hr) that accounts for the peak 5-min interval within the hour. b.) Determine the maximum flow rate (veh/hr) that accounts for the peak 15-min interval. c.) Determine the peak hour factor, based on peak 15 – min counts.
The average queue length at the intersection of the two roads with a stop sign is 4 vehicles. If the arrival rate of vehicles at the stop sign is 300 veh/hr, determine the service rate of the road in veh/hr. Assume both arrival and departure rates are exponentially distributed.
QUESTION 1 3 booths, each of which can handle one vehicle every 6 second. a. If D/D/1 model is used, what is total service rate of the system? (you can express this in total vehicles that can be handled in 10 minutes) 6. Draw the queuing diagram (cumulative traffic volumes vs. time) with traffic upstream arriving volume and this service rate. C. Using the queuing diagram, determine the max queue, the longest delay to an individual vehicle and total delay (veh-min). Time Period 10-min Volume 7:00-7:10 200 स 7:10-7:20 400 7:20-7:30 500 7:30-7:40 250 7:40-7:50 200 7:50-8:00 150
There is a single gate at an entrance to a recreational park where arriving vehicles must stop to pay their tickets. The park opens at 8:00AM, at which time vehicles begin to arrive at a rate of 480 veh/hr. After 20 minutes the arrival flow rate declines to 120 veh/hr, and it continues at that level for the remainder of the day. If the service time is 15 seconds per vehicle, and assuming D/D/1 queuing, determine the Length of Queue at 8:1OAM. Note: Round off your answers to the nearest whole number. Only include the numeric value of your answer without the unit (i.e. 22).
There is a single gate at an entrance to a recreational park where arriving vehicles must stop to pay their tickets. The park opens at 8:00AM, at which time vehicles begin to arrive at a rate of 480 veh/hr. After 20 minutes the arrival flow rate declines to 120 veh/hr, and it continues at that level for the remainder of the day. If the service time is 15 seconds per vehicle, and assuming D/D/1 queuing, determine the Longest Vehicle Queue. Note: Round off your answers to the nearest whole number. Only include the numeric value of your answer without the unit (i.e. 22).
There is a single gate at an entrance to a recreational park where arriving vehicles must stop to pay their tickets. The park opens at 8:00AM, at which time vehicles begin to arrive at a rate of 480 veh/hr. After 20 minutes the arrival flow rate declines to 120 veh/hr, and it continues at that level for the remainder of the day. If the service time is 15 seconds per vehicle, and assuming D/D/1 queuing, determine the time that the queue will dissipate. Answer must be in this format: *:**AM, minute time must be rounded off to the nearest whole number (i.e. 8:50AM)
2. Congestion starts at 6am in an expressway. Survey found out that an average of 600vph entered the expressway for the 1* 30minutes, reduced to 250vph and remain constant for the succeeding hours. The booth teller took approximately 10sec to render its service for every vehicle. a. Determine the time of dissipation b. Calculate the total number of vehicles entered for this duration Determine the queue and delay after 45mins from the start of rush hour d. Calculate the delay experienced by the 100th vehicle C.
The arrival rate at a parking lot is 6 veh/min. Vehicles start arriving at 6:00 P.M., and when the queue reaches 36 vehicles, service begins. The company policy states that the total vehicle delay should be equal to 500 veh-min. Assuming D/D/1 queuing and a constant service rate, what is the departure rate?
The maximum number of vehicles observed in any five-minute period during the break hour is 160. If the total flow in the peak hour is 1000 vehicles, the five-minute peak hour factor (round off to 2 decimal places) is
The maximum number of vehicles observed in any five minute period during the peak hour is 160. If the total flow in the peak hour is 1000 vehicles, the five minute peak hour factor (round off to 2 decimal places) is