1.) The beam has a width of 300 mm, an overall depth of 600 mm, and an effective depth of 520 mm. The beam is simply supported over a span of 9 meters and carries a superimposed dead load of 8 kN/m and a live load of 20 kN/m. The specified compressive strength is 21 MPa and Fy = 345 MPa. Determine the required stirrup spacing near the support. Use 10 mm vertical U- stirrup with fyt = 275 MPa. Use detailed calculation for Vc. wd, wL

1.) The beam has a width of 300 mm, an overall depth of 600 mm, and an effective depth of 520 mm. The beam is simply supported over a span of 9 meters and carries a superimposed dead load of 8 kN/m and a live load of 20 kN/m. The specified compressive strength is 21 MPa and Fy = 345 MPa. Determine the required stirrup spacing near the support. Use 10 mm vertical U- stirrup with fyt = 275 MPa. Use detailed calculation for Vc. wd, wL

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Check the adequacy of the isolated T-beam shown below according to ACI Code requirements and determine the design flexural strength (Moment) for it, use: • f = 20 MPa. • fy = 420 MPa. Effective depth d = 610 mm. • Reinforcement is 6Ø25mm (ABar = 490 mm?). 500 mm 125 mm 700 mm 6Ø25mm 250 mm
Q2: A cantilever beam AB, loaded by a uniform load and a concentrated load, is constructed of a channel section. Find the maximum tensile stress g and maximum compressive stress gc. 15 N 20 N/m 40 mm 40 mm F 225 mm- 40 mm 200 mm 2.5m 0.5 m
A T-section has a flange width of 750 mm, thickness of flange is 50mm. Effective depth is 750 mm with a width of web section of 350 mm. The beam is subjected to a factored moment ??=816 kN-m, concrete has a strength of 21 MPa and that the yield stress of the steel is 277 MPa. Determine the following:a. Nominal moment capacity of the overhanging portion of the section.b. Depth of the compression blockc. Area of reinforcemen
. In reinforced beam having a width of 300 mm and an effective depth of 600 mm, carries a moment of 80 kN-m, which developed a stress (fc) of 5 MPa in the Concrete. Considering Cracked Analysis. a) If n = 9, compute the distance of the neutral axis from the top of the beam. Hint kd = k x d. Note: k < 1.0 O 200.000 mm O 229.180 mm O None of the Choices O 259.688 mm O 145.017 mm O 171.989 mm
4-5 The A-36 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is 60 mm², determine the displacement of B and A. Neglect the size of the cou- plings at B, C, and D. 60° 3.30 KN 2 kN D C B A 8 kN 60⁰ 3.30 KN 0.75 m 1.50 m 0.50 m 2 kN
4-43 The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be consid- ered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400 mm². Eal = 70 GPa. A 100 mm- B 100 mm- C 800 kN/m 125 mm 11800 800 kN/m
The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm, the web thickness is t-12 mm. Determine the maximum tensile and compressive stresses in the beam due to uniform load. And draw. 3.2 KNi m 400 mm 2 KN.M BO 80 mm 12 mm 3m 1.5m
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I V : 4 H and distance between trusses is equal to 6 m. The purlin has a weight of 79 N/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 720 Pa, live load of 1000 Pa and wind load of 1.2 1.2 1440 Pa. Coefficient of Purlins pressure at leeward and windward are 0.6 and 0.2 respectively. Assume all loads passes through the centroid of the section. Properties of C 200 x 76 mm Sx = 6.19 x 104 mm Sy = 1.38 x 104 mm3 W = 79 N/m 1.2 Truss 1.2 12 12 1.2 Allowable bending stress Fbr = Fby = 207 MPa Truss %3D 6m O Calculate the bending stress, fox, for dead load and live load combination (D + L). Calculate the bending stress, foy, for dead load and live load combination (D + L). O Calculate the maximum ratio of actual to the allowable bending stress for load combination 0.75 (D + L + W) at the windward side. fbx = 151.14 MPa fby = 169.6 MPa Interaction = 1.25
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I V: 4 H and distance between trusses is equal to 6 m. The purlin has a weight of 79 N/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 720 Pa, live load of 1000 Pa and wind load of 1.2 1.2 1440 Pa. Coefficient of Purlins pressure at leeward and windward are 0.6 and 0.2 respectively. Assume all loads passes through the centroid of the section. Truss Properties of C 200 x 76 mm Sx = 6.19 x 104 mm Sy = 1.38 x 104 mm W = 79 N/m 12 12 1.2 I Allowable bending stress Fbx= Fby = 207 MPa Truss %3D 6m O Calculate the bending stress, fox, for dead load and live load combination (D+ L). Calculate the bending stress, foy, for dead load and live load combination (D + L). O Calculate the maximum ratio of actual to the allowable bending stress for load combination 0.75 (D + L + W) at the windward side. fbx = 151.14 MPa fby = 169.6 MPa Interaction = 1.25
Consider the loads of the figure to be axially applied at sections B, C, and D to the concrete structure supported at A. IW E F P G 5 kN 5 kN A Determine P in kN when member BC is 24 mm in diameter, the axial stress in section F is 588 MPa, and W 309822 N. = 10 kN C 10 kN Rigid -bearing plates
From the given figure below, determine the maximum flexural stress of the beam if it has a cross section of 150mm wide by 250mm deep. (JN 10 N/m o' RA=42N 42N 3M B IM 75Nm 81NM Im RD=3N -3N 0° 78 Nm 3NM V-DIAG M-DIAG
2. Design the compression member in Problem 1 using W14 and A-50 steel. Use ASD with PDL= 990 KN AND PLL= 680 KN. muu 2.5m 3.5m 3.5m I