1. The canal shown in cross-section in the figure below runs 20m into the page. a) Determine the horizontal and vertical components of the hydrostalic force against the quarter circle wall AB. b) Sketch the hydrostatic pressure distribution (thrust per unit area) on the wall AB. Show supportive calculations. 18m 18 m Water

1. The canal shown in cross-section in the figure below runs 20m into the page. a) Determine the horizontal and vertical components of the hydrostalic force against the quarter circle wall AB. b) Sketch the hydrostatic pressure distribution (thrust per unit area) on the wall AB. Show supportive calculations. 18m 18 m Water

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.88P: Compute the surface area of the axi-symmetric domed structure.

See similar textbooks

Similar questions

Compute the surface area of the axi-symmetric domed structure.
5. Gate ABC is shaped in the form of a circular arc and pivots about point O. The arc extends a width b in the plane of the figure. 6 m Water A R = 6m 6 m Questions: (a) Determine the horizontal component of the resultant hydrostatic force (per unit width) acting on the gate. (b) Determine the vertical component of the resultant hydrostatic force (per unit width) acting on the gate. (c) Determine the magnitude and direction of the resultant hydrostatic force. (d) Does the line of action of this force pass through point O? Justify your answer.
): Find the hydrostatic pressure force acting on the ABCD curvilinear surface. (The width of the gate is 3 m). Draw hydrostatic pressure distribution on this figure. 2.4m Water Water 1.6 m ANAA
Solve for the hydrostatic force per meter length acting on the radial tainter as shown in the figure. Unit Weight is 9.81 kN/cu.m. R=4 ANGLE = 43 RADIUS ANGLE O 78.664 O 241.707 O 79.254 O 123.052 M
1- Panel BC in the figure is circular. Compute (a) the hydrostatic force of the water on the panel; (b) its center of pressure; and (c) the moment of this force about point B. Given and unknowns: Assumptions: Schematic: Governing Equation(s): Analysis and Results: Water at 20°C C 50° B 3 m 3 m 3 m
SEA WATER T SIDE FRS 7M Faf FRESH WATER SIDE As shown in the figure, a vertical wall Seperates a seawater-filled tank and a freshwater-filled tank from each other. Since the depth of seawater is 7 meters a) How deep should the fresh water be for the compound force on the wall to be Jero? 2 b) is the moment created by the fluid forces gero when the resultent force on the wall is gero? Explain.
A vertical dam has a semicircular gate as shown in the figure. The total depth d of the figure is 12 m, the height h of air above the water level is 2 m, and the width w of the gate is 10 m. Find the hydrostatic force (in N) against the gate. (Round your answer to the nearest whole number. Use 9.8 m/s2 for the acceleration due to gravity. Recall that the weight density of water is 1,000 kg/m³.) 1040542 12 m XN 10 m 2 m water level Ⓡ
The cylinder shown in the figure extends 10 ft into the paper. If the cylinder has the radius of 4 ft, compute the vertical component of the hydrostatic force of the oil on the cylinder. 90 Oil (s.g. = 0.85 ) %3D 4 ft 50°
A trapezoidal plate shown in the figure is submerged in water is 3.2 m below the surface. The bases of the plate is 2 m and 7 m, respectively. The height is 9 m. Find the location of the force from the bottom in meters. Unit weight of water is 9.78 KN/m³. Answer is in KN. Write only the value of your answer. FFS
ester SY 2021 ements utton Solve for the hydrostatic force per meter length acting on the radial tainter as shown in the figure. Unit Weight is 9.81 kN/cu.m. R = 5 ANGLE = 40 RADIUS ANGLE 316.156 O 122.813 79.254 212.562
The flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 9810 N/m. 6m 5m 8m Enter the exact answer. F = %3D
The cross-section of an open tank is shown below at left. BC is a cylindrical surface with radius r = 6 ft, and the tank water depth is h = 10 ft. A free body diagram (FBD) for hydrostatic analysis is shown below at right. Use this information to solve problems 12 through 15 on a per unit width (into the page) basis. FBD: A B B OThe magnitude of the horizontal force Fy is nearest 1a) 490 lb/ft width of tank (b) 1610 Ib/ft width of tank (c) 3120 Ib/ft width of tank (d) 12.5 Ib/ft width of tank (e) None of the above are close to being correct ) The center of pressure Yp is ft below the water surfa The magnitude of the vertical hydrostatic force Fy is nearest (a) 1765 Ib/ft width of tank (b) 3744 Ib/ft width of tank (c) 1980 Ib/ft width of tank (d) 10.4 Ib/ft width of tank (e) 675 Ib/ft width of tank The location of Fy left of side AB is nearest ft OST or DISTREBUTE - THANK YOU