1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 Ib-in. The total angle of twist must not exceed 3 degrees per 100 ft. the maximum shearing strength must not exceed 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find the maximum torsional shear stress and (c) Find the maximum torsional shear strain.

1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 Ib-in. The total angle of twist must not exceed 3 degrees per 100 ft. the maximum shearing strength must not exceed 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find the maximum torsional shear stress and (c) Find the maximum torsional shear strain.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 lb-in. The total angle of twist must not exceed 3 degrees per 100 ft. the maximum shearing strength must not exceed 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find the maximum torsional shear stress and (c) Find the maximum torsional shear strain.
A steel shaft 2573 mm long must transmit a torque of 34 KN-m. The total angle of twist and the maximum shearing stress must not exceed 3 degree and 110 MPa respectively. Find the diameter of the shaft that meets there conditions. Check based on strength and rigidity. Use G = 78268 MPa. Use two (2) decimal places.
Find the torsional shear stress on a 2 inch diameter shaft if it is subjected to a torque of 561 in-lb.
A solid steel shaft of circular cross-section has diameter 50 mm, length 1,028 mm and shear modulus 79.3 GPa. If the allowable shear stress is 36 MPa and the allowable angle of twist is 1.9°, determine the maximum permissible torque. Give your answer in Nm to 1 decimal place.
A hallow steel shaft 2540 mm long must transmit torque of 34 KN-m. The total angle of twist must not exceed 3 degrees. The maximum shearing stress must not exceed 110 MPa. Find the inside diameter and the outside diameter of the shaft that meets these conditions. Use G = 83 GPa
A hollow steel shaft 2540 mm long must transmit a torque of 34 kN-m. The total angle of twist must not exceed 3 degrees. The maximum shearing stress must not exceed 110 MPa. Find the OUTSIDE DIAMETER and INSIDE DIAMETER of the shaft that meets these conditions (in mm). Use G = 83 GPa.
A solid steel bar with a circular cross-section has diameter 50 mm, length 1.5 m and shear modulus of 80 GPa. If the allowable shear stress is 48 MPa and the allowable angle of twist is 2.0 degrees, then what is the maximum permissible torque? State your answer in Nm to 1 decimal place.
À solid 0.96-in.diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 Ib-A 50 Ib-ft 70 Ib-ft (1) (2) 30 Ib-f (3) 827 psi O 880 psi O 956 psi 691 psi O 739 psi
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft 50 lb-ft 70 Ib-ft | (1) 30 lb-ft A (3) B D 3150 psi O 2524 psi 1876 psi O 2331 psi O 2932 psi
Ahollow shaft with an external diameter of 150 mm transmits a maximum torque of 13 kNm. The shaft length is 5 m,and the maximum shear stress is limited to 40 MPa. If G = 84 x 103N/mm2, calculate;2.1 the internal diameter of the shaft.2.2 the angle of twist in degrees.2.3 the minimum shear stress in the shaft.
1) What is the minimum diameter of a solid steel shaft that will not twist through more than 3° in a 6 meter length when subjected to a torque of 14k N.m?What maximum shearing stress is developed ?Use G=83GPA.
The end of a 2.5 in diameter steel shaft is milled to two flats (one flat on the top and one flat at the bottom) to permit the use of a hand crank. Each flat is located 1.00 in from the center of the shaft. A torque of 750 Ib-in is applied. Find: (a) the maximum shear stress at the end of the shaft with two flats in psi unit. (b) the angle of twist in fadians (c) the angle of twist in degrees h= 1.0 in h= 1.0 in d= 2.50 in Show all your calculations.