1. Using the Multi-sim, connect the circuit Shown in Fig.(2), and take Vy-10V, and R 820, R- 1002 and Ry -1502. 2. Measured the voltage and current of "R,, R. & R;", then record it in table below 3. Disconnect the DC power supply, and then measured the equivalent resistance by using the AVO meter only.

1. Using the Multi-sim, connect the circuit Shown in Fig.(2), and take Vy-10V, and R 820, R- 1002 and Ry -1502. 2. Measured the voltage and current of "R,, R. & R;", then record it in table below 3. Disconnect the DC power supply, and then measured the equivalent resistance by using the AVO meter only.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.30P: Reconsider Problem 3.29. If Va,VbandVc are a negative-sequence set, how would the voltage and...

See similar textbooks

Similar questions

Design a 24v zener regulated power supply circuit that will power a 500 ohms load with 1A of of current. Determine the power rating of both bleeding resistor and load resistor. Note the computed power dissipation differ from the required power rating of the device.
For an RTD the relationship between resistance and temperature is a. proportional b. no relation c. equal d. inversely proportional
With no load attached, the voltage at the terminalsof a particular power supply is 50.8 V. When a 10-Wload is attached, the voltage drops to 49 V.a. Determine vS and RS for this nonideal source.b. What voltage would be measured at the terminalsin the presence of a 15- load resistor?c. How much current could be drawn from this powersupply under short-circuit conditions?
Question 3: If the currents are in the same direction for a pair of parallel running wires, the currents on the wires are referred as Common Mode currents, ICM. On the other hand, if one of the currents is running in reverse direction (as they should normally do), the currents are referred as Differential Mode currents, IDM. It is essential in analog circuit design to keep track of differential and common mode currents. Referring to the following illustrations, assume that the separation between the wires, d, is 4 mm, the magnetic field observation point, S, is 20 mm away from the right wire, ICM- 5 mA, and IDM= 150 mA.
The drawback to using this equivalent circuit, however, is that it is defined for a set of operating conditions that might not match the actual operating conditions. a.pi b.hybrid-pi c.hybrid d.re
Perform a theoretical analysis on the circuit to determine the following using nominal values: a. It, Pt, V drop across each resistor, and I through each resistor, and Power dissipated each resistor. b. Determine Vab, Vac, Vad, bc, Vdb.
FACTS: AC-DC converters take the AC power from wall outlets and convert it to unregulated DC. These power supplies include transformers that change the voltage of the AC that comes through wall outlets, rectifiers to save it from AC to DC and a filter that removes noise from the peaks and troths of the AC power waves.The DC-to-AC Converters are used to charge the batteries in the vehicles. These circuits are mainly used for driving low-power AC motors and are used in a solar power system. The DC to AC converters can be used in dc transmission lines for transmitting power to loads. QUESTION: What do you think is the main reason why we have AC power in our outlets instead of DC power? Explain your answer.
1) The term Bi is defined as Select one: O a. Negative change in reference bus power to the power change DPi on bus i O b. All of these 1/Pfi Clear my choice
A chopper is employed to charge a battery as shown in figure. The charging current is 5 A. The duty ratio is 0.2. The chopper output voltage is also shown in the figure. The peak to peak ripple current in the charging current is https://practicepaper.in/wp-content/uploads/GATE/EE/20031/q87.jpg
The circuit given below consists of some components that value.R is the value of "92". V1 is the voltage value given by the "6".a-) According to defined prerequisites for the circuit, redesign the schematic.b-) the variable DC voltage source in the circuit given below is adjusted so that i0 is zero. Find the value of VDCc-) Is there a power dissipating source in the circuit? Verify your answer
In the circuit below, if the inductance L is large enough to operate in continuous current mode. a) Draw the waveform of the output voltage and mains current for the 45 degree trigger angle when the switch S is in transmission. b) Average value of output DA voltage VDC1 when switch S is open, output DA when switch S is closed (in transmission) If the average value of the voltage is VDC2, calculate the value of VDC1 / VDC2. Lesson: power electronics please quick
A PMMC instrument has internal resistance of 0.63 kQ and gives full scale deflection for 31 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 64 V will be ohms. O a. 205.82 O b. -145.62 O c. 1434.52 O d. 101556.30