100 kN lsize as sho 80 [A find the diameter of the rivet. 18. A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as shown in Fig. 9.39. A load of 100 kN is applied to the bracket at an angle of 60° to the horizontal and the line of action of the load passes through the centre of the bot- tom rivet. If the maximum shear stress for the material of the rivet 80 80 K60° is 70 MPa, find the diameter of rivets. What will be the thickness of the plate if the crushing stress is 100 MPa? [Ans. 29 mm; 1.5 mm] All dimensions in mm. Fig. 9.39

100 kN lsize as sho 80 [A find the diameter of the rivet. 18. A bracket in the form of a plate is fitted to a column by means of four rivets of the same size, as shown in Fig. 9.39. A load of 100 kN is applied to the bracket at an angle of 60° to the horizontal and the line of action of the load passes through the centre of the bot- tom rivet. If the maximum shear stress for the material of the rivet 80 80 K60° is 70 MPa, find the diameter of rivets. What will be the thickness of the plate if the crushing stress is 100 MPa? [Ans. 29 mm; 1.5 mm] All dimensions in mm. Fig. 9.39

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the rivets connecting these plates to the outside plates is 1 in. If the allowable unit stress in tension on the net area is 20,000 psi, the safe tensile strength of eith central plate is A. 90,000 lb B. 88,600 lb C. 78,600 lb D. 75,800 lb
Q1/ Calculate the forces in all rivets for the rivet group shown. 24KN 600mm 300mm 240mm
(3) Hard drawn copper rivets are used to join the two plates shown. What diameter rivets should be used for a factor of safety of 2? (ans. 0.36 in) 1200 lb 1200 Ib
Two steel plates linked together via a double riveted butt joint is subjected to the load P. Assume that the applied load distributes evenly among the ten identical rivets and neglect friction. a. Draw the FBD of a middle plate and that of a cover plate. Label forces as a function of P. b. Draw the FBD of a rivet. Do all rivets experience the same shear stress? Why or why not? c. How many unique values of the bearing stress can be solved? Enumerate all. d. What is the maximum tensile stress in the middle plate? in the cover plate? Answer in terms of P. Use the following dimensions: diameter of rivets - 10 mm, thickness of cover plates - 15 mm, thickness of middle plates - 25 mm, width of both plates-100 mm. P- P- P -P
A steel plate is hoisted by a cable sling that has clevis at each end as shown in the Fig.1. The total weight of the plate is 100 kN. The pins through the clevises are 20 mm in diameter. The cable has diameter of 25 mm. Each half of the cable is at an angle of 35° to the vertical. Using factors of safety of 2 for normal stress and 3 for sheer stress, check if the mechanical system is safe. Ofail.cable = 250 MPa and tfail.pin 100 MPa Cable sling 35 35 Clevis Steel plate
A 5.0m long steel wire has a cross-sectional area of 0.55cm^2. Its proportional limit has a value of 0.0018 times its Young's modulus. Its breaking stress has a value of 0.0065 times its Young's modulus. The wire is fastened at its upper end and hangs vertically. a. How great a weight can be hung from the wire without exceeding the proportional limit? b. How much will the wire stretch under this load? c. What is the maximum weight that the wire can support?
1. You are to design an axially loaded member that is to carry a load of 5,000 lb. The member is to be made of ASTM A36 steel and have a total length of 24 in. Due to the design requirements the maximum allowable elongation of this member under the stated load is 0.025 in. Find the smallest allowable diameter of the member. a. Given: PL where ô is member elongation, P is axial load, L is initial member length, E is the material's Modulus of Elasticity, EA and A is the member's cross section area E136 = 29*10° psi (Beer, 746)
Seatwork: Show your complete solution. Use 4 decimal places. Poisson’s Ratio: A square bar of aluminum 40 mm on a side and 220 mm long is loaded by axial tensile forces at the ends. Experimentally, it is found that the strain in the direction of the load is 0.001. Determine the volume of the bar when the load is acting. Considering a Poisson’s ratio of 0.33
The lap joint shown is fastened by four 314" dia. bolts. Assume the applied load is uniformly distributed among four rivets. The width of plate is 5 inch with 1/2 inch thick and a tensile stress is 16 ksi. (assume that hole is greater than fasteners by 1/8") 00 a) What is the value of the external load "P" that the plate could carry? .b) What is the shear stress of the rivet? c) What is the bearing stress of the of the plate? .d) If the % bolt is replaced with 1" dia. bolt, what is the tensile stress of the of the plate? P.
1. A rectangular bar is originally 3.00 inches wide X 0.25 inches thick. What axial load (in pounds) must be placed on the bar in order for the thickness to decrease by 0.002 inches? Use E = 10E6 psi and Poisson's ratio of 0.30.
The bar in the attached picture has a thickness of 16mm and a total width of 48mm. The pin has an diameter of 11mm.....
A book is to be mounted on a wall as shown. Weight, W, is 2000N. Shear stress in the bolts should not exceed 60MPa. Determine the minimum standard diameter of the metric bolt/screw that should be used.