100 mm 300 mm 60 mm 150 mm Water flows out of the pipe at B with a velocity of 10 m/s at atmosphere. Neglect the weight of the elbow and the water within it at any given time. Also neglect any forces/moments transmitted to the system by the pipe connection at C (the pipe at C is enclosed and not open to atmosphere). Recall that for water Pw = 1000 kg/m. Answer the following: 3a. Draw both the control volume and free-body diagram for this problem 3b. Determine the pressure at location C Determine the horizontal and vertical components of force as well as the moment developed at the fixed connection at A 3c.

100 mm 300 mm 60 mm 150 mm Water flows out of the pipe at B with a velocity of 10 m/s at atmosphere. Neglect the weight of the elbow and the water within it at any given time. Also neglect any forces/moments transmitted to the system by the pipe connection at C (the pipe at C is enclosed and not open to atmosphere). Recall that for water Pw = 1000 kg/m. Answer the following: 3a. Draw both the control volume and free-body diagram for this problem 3b. Determine the pressure at location C Determine the horizontal and vertical components of force as well as the moment developed at the fixed connection at A 3c.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

%TE l, UPUOM A 9;Y) 团 / د امتحان مد1.docx The pipe assembly is subjected to the force of F = {600i + 800j – 500k} N Determine the moment of this force about point B. 0.5 m 0.4 m 0.3 m 0.3 m II
& HYDRAULICS Total Hydrostatic Force on Surfaces Problem 3 - 104 Water in a tank is pressurized to 80 cmHg. Determine the total force per meter width on panel AB. Ans: 482 kN 2 m 80 cm Water 4m Hg 3 m Problem 3 - 105
1. Water flows through Pipe A and into parallel pipes 1,2 and 3, and out through Pipe B. The properties of the pipes are listed as follows: Pipe Length (m) Diameter (cm) 30 Friction Coefficient, f A 1 300 10 0.020 240 600 2 15 0.018 3 20 0.017 В 30 The upstream junction (near A) has an elevation of 90m with a pressure of 205 KPa; the downstream junction is at elevation 30 m. If the average velocity in Pipe A is 3.0 m/s, find the pressure at the downstream junctions and rate of flow in each pipe. Also, draw the pipe system.
L11)! 111 1........ Date No. A differential manometer is connected. at two poins A and B of two pipes as Shown on the belw figure, The pipe A Contains a liquid of sp.gr= lo5 while B contains aliquid of sp.gr=0.9. The pressure. at A and B are 9.81 X l04 N/M and 1.8 X 10u N /my respectively. Density ot mercury 13.6 g/cn². Find the difference în mercury level in the diffenential mano meter. sp.gr=Dl05 3m 2.0 Sp.gr=o9
Problem 5. (20 pts) Calculate the total hydrostatic force and the location of the center of pressure (y,) acting on the inclined, circular gate with water on one side as shown. Given that the radius of the gate is 1 meter. 60 1. Sm sin60 1. 5m Yes 1m sin60" m yer
Water in the reservoir is used to control the water pressure in the pipe at A. Take pHg = 13550 kg/m³ and p = 1000 kg/m³ Neglect the diameter of the pipe. (Eigure 1) Figure AQ B E h 400 mm C 150 mm 100 mm 200 mm Mercury pe he Y Part A If h= 140 mm, determine the gage pressure in the pipe at A when the mercury is at the elevation shown. Express your answer to three significant figures and include the appropriate units. PA 76.8 Submit 4 Provide Feedback kPa CINC Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining
What is the difference between the pressure at the two sections? * :A horizontal pipe , I P4 in diameter, taperv gradually to 8 in. in dia meter. If the flow ir 500 cu f4 of water per minute, what i the difference between the presure at the two sections? Given : Quyo ® 500 ft³/min do 8" O 445.66 psf O 417.65 psf O 455.89 psf O 420.11 psf O 432.37 psf
Pipe 1 which is 150 mm in diameter and 300 m long is in parallel to pipe 2 which is 500 m long. Pipe 1 carries 150 liters per second while pipe 2 carries 190 liters per second. What is the diameter of pipe 2 if the friction factor for both pipes is the same? Select one: O a. 178 mm O b. 196 mm O c. 183 mm O d. 165 mm
Water flows from A to E through the pipe system shown. It is known that the flow in pipe BFGC IS 30 LITERS /SEC. and that the pressure head at A is 60 m. Assuming that f =0.022 and that all the pipes are level, determine the total flow from A to E and the pressure heads at B, C, D and E.
3. Obtain the gage pressure at the center A of the pipe shown. Ignore surface tension effects. Given: Liquid 1 S.G. = 1.5 Liquid 2 S.G. = 3.2 hi = 15 cm h2 = 30 cm h3 = 75 cm a. 589 Pa с. 452 Ра d. -452 Pa b. -589 Рa Liquid 1 Liquid 2 X1 h,
Water flows through 150 mm diameter pipe AB 400 m longThe point B is 20 m above A. The discharge through the pipe is 0.02 m³/sec from A to BFind the pressure at A if the pressure at B is 200 kPa. Take f= 0.006.
Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1 and 2 are found to be 20 psi and 25 psi, respectively. The elevation of point 1 is 12 feet, and the elevation of point 2 is 0 feet. There are 15 feet of pipe between the two points. Determine the direction of flow. flow is from point 1 to point 2 flow is from point 2 to point 1 water does not flow between point 1 and point 2 [continued from previous question] Water flows in a pipe of 1-in. diameter at a temperature of 70°F. The pressure values at points 1 and 2 are found to be 20 psi and 25 psi, respectively. The elevation of point 1 is 12 feet, and the elevation of point 2 is O feet. There is 15 feet of pipe between the two points. What is the minimum discharge above which the flow will not be laminar? Report your answer in gallons per minute (gpm) with 2 decimal places.