11. Design the combinational circuit that would have 2 selector lines and having the out put equal to =10 when both selectors are HIGH and 13 when both are LOW and 11 when MSB of selector line is HIGH and LSB is LOW and 12 when MSB of selector line is LOW and LSB is HIGH. Write necessary truth table, Logical expression and Logical diagram

11. Design the combinational circuit that would have 2 selector lines and having the out put equal to =10 when both selectors are HIGH and 13 when both are LOW and 11 when MSB of selector line is HIGH and LSB is LOW and 12 when MSB of selector line is LOW and LSB is HIGH. Write necessary truth table, Logical expression and Logical diagram

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Build the 1-bit full adder circuit and convert it into symbol (block). Write a detailed explanation about the full adders. Insert your screenshot and the explanation here 2. Build the 4-bit adder circuit and convert it into symbol (block). Write a detailed explanation about how it works. Insert your screenshot and the explanation here 3. Build the 4-bit adder subtractor and convert it into symbol (block). Write a detailed explanation about how it works. Insert your screenshot and the explanation here 4. Build the 7 Segment Decoder and convert it into symbol (block).
What will be the final value of DI after executing the following piece of code? Execute the instructions dependently one after another. CLD MOU CX,OFOH MOU AX,05678H MOU DI,01000H MOU ES, DI SUB DI, DI REPNZ SCASB -R AX-0000 DS-073F 073F:0100 0000 D 1000:0 F 1000:0000 92 00 14 12 54 56 44 78-AD 56 78 FO 00 00 00 00 BX-0000 CX-0000 DX-0000 SP-00FD ES-1000 SS%3073F CS=073F BP-0000 SI=0000 DI=0000 IP-0100 NU UP EI PL NZ NA PO NC ADD IBX SI1,AL DS:0000 CD TUDX.Ux..... .... Notes: 1- Use the DEBUG window to answer this question (values shown are prior to execution and in hexadecimal 2- Write down the final value of DI as four hexadecimal digits without any additional characters.
I need to implement the 1-4 with 1-bit demultiplexer in a diagram. How to draw it. and how to do the final equation
Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. X Y Figure_6 Part 4:The data-input and data-select waveforms in Figure 7 are applied to the multiplexer. Determine the output waveform F in relation to the inputs. DO D1 D2 D3 1. SO s1 Figure_7
5) Rebuild the instructions a- INC CX b- SUB AI,02H c- SUB AX,DX 6) Compare between SUB & CMP instructions
Consider the circuit given in the figure, where clocks are same and positive edge triggered are connected toD FFs. The states marked in the state table is designated as a two bit Q0 Q1. Let the initial state be 00. Then the correct state diagram is 00 11 01 0 + 11 00 10 01→ 11 00 11 01 → 10 cik re to search Ae
Adocs.google.com is a logic switch that select information from one of the input line and directs it to a single line Encoder Decoder Adder Multiplexer Binary to octal can be implemented used 3-8 De-Multiplexer Multiplexer Decoder Encoder System base 12 include numbers from ... to .... 1-B 1-C 1-12 1-11 ۹:۰۳ F
Procedure: You are to design a 4-bit arithmetic unit that consists of a 4-bit adder/subtractor circuit. The arithmetic unit takes as inputs two 4-bit numbers (A and B) and one control input (M) add/subtract selector that selects the type of operation the unit will perform. When the input control is ‘0’, the input numbers are added. When it is set to ‘1’, the two input numbers are subtracted (A - B). Question: Two 4-bit Adder/Subtractor Circuit: Design and construct a 4-bit adder/subtractor circuit. Draw the produced circuit.
Write Arduino program that will add two bit binary numbers and calculate the sum ofboth numbers. You have two show both numbers on seven segment as well as sum of bothnumbers will also be display on seven segment.
Consider the following registers - AX contains 1122h, BX contains 3344h, CX contains 5566h and DX contains 7788h. ( You don't need to write code for this part) Write code to consolidate these value to two 32-bit registers - EAX and ECX. After executing your code, EAX should contain 11223344h and ECX should contain 77885566h. You are NOT allowed to mov any immediate values to the registers. h. Add a File Record Audio Listen
Transfer Instructions H.W2 Write the necessary instruction to change or swap 3 byte stored at DS:0A60 with DS:0A80 Solution:
In the following circuit, X and Y values are connected to the Multiplexer inputs. Decimal values of X and Y are given as follows: X= - 2 Y= - 12 Note that both X and Y have negative values and they are represented in TYPE 2 representation, where Type 1:One's complement Type 2: Two's complement Type 3: Signed Magnitude a) Find 4-bit input values X3 X2 X1 X0 and Y3 Y2 Y1 Y0. b) Find the boolean expression for the function F2 in terms of variables A, B, C, D. c) Simplify the function you found in part b) using the karnaugh map method. Do not forget to write down the decimal value of X, Y and the representation type in your solution. |Cin хо 10 YO 10 A S F1 11 4:1 11 4:1 X1 Y1 X2 12 Mих Y 12 Mux Cout F2 Y2 • B X3 13 Y3 13 FULL si so si so ADDER А В C D