-12V R2 680 Ohm Supply Voltage 12VDC R1(2 1 kOhm R4 1.5 k Ohm R3 4.7 kOhm (Y) Figure 8: Series-parallel circuit 2. Using the VOM, measure and record the voltage and current in your circuit. (1 mark) Table 1: VOM Readings VR1 VR2 VR3 VR4 2.55 3.75 5.64 11.97 3. Answer the questions in Skills Testing. T

-12V R2 680 Ohm Supply Voltage 12VDC R1(2 1 kOhm R4 1.5 k Ohm R3 4.7 kOhm (Y) Figure 8: Series-parallel circuit 2. Using the VOM, measure and record the voltage and current in your circuit. (1 mark) Table 1: VOM Readings VR1 VR2 VR3 VR4 2.55 3.75 5.64 11.97 3. Answer the questions in Skills Testing. T

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES
(5) Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor in Non- linear Load Figure 6 Analyse different methods of harmonics mitigation to eliminate the harmonic, which you have identify in above power system circuit. You can use harmonic filters, K or equivalent transformers or oversized neutral method depending upon the harmonic sources.
Q2/3-phase.E.W.C. R using center tap transformer supplies highly inductive load, find: 1. The average load voltage with and without FWD and discusses these cases. 2-lf firing angle equal to 45°, the supply voltage is240v, transformer ratio is (2/1). Calculate the DC current& voltage of this case. 3- Draw all waveforms diagram. 4- what are the difference between the type of connection (Delta or Star).
Combination circuit what is PT? RT? IT? Voltage Across each load?
Consider Two same size series connected PV modules,each with the specification as Po=100W, Voc= 24.5V and Isc=5A.then choose the correct Statement Refer to this PV Panel. a.The output power from this panel is 100W , the Voltage is 24.5V and the current is 10A b.The output power from this panel is 200W , the Voltage is 24.5V and the current is 10A c.The output power from this panel is 200W , the Voltage is 49V and the current is 5A d.The output power from this panel is 200W , the Voltage is 49V and the current is 10AClear my choice
What are the applications of clamper circuits? Enumerate 3. Provide references.
Identify the characteristics of AC and DC voltage. Runs at a higher temperature Answer 1Choose...DCAC More dangerous to transfer Answer 2Choose...DCAC Easy to produce Answer 3Choose...DCAC Easier to transform voltages Answer 4Choose...DCAC Voltage remains at a constant value Answer 5Choose...DCAC Cheaper to produce
Q1. a) An SCR based AC power controller circuit is given in Figure 1. The circuit connects a 240V 50Hz AC source vi to a resistive load with resistance of 100. If the delay angle is a-15°, draw the waveforms of the load voltage Vo, and the voltage across SCR2. Calculate the power supplied to the load. + Vi Va + 2 SCR2 H₁₁ SCR₁ Figure 1 SCR based AC power control circuit Va + 2 io b) Figure 2 is a single phase 2-level voltage source converter (VSC) with a DC voltage Vd-200V. A PWM scheme, by comparing a reference value with a 10kHz triangle waveform, is used to control the switches S₁ and S2. The modulation index of the PWM is m=0.8. With the aid of graphs explain how pulse signals for the switches are generated, sketch the output voltage Vo, determine the duty cycle, and calculate the average output voltage. + Vo + Vo √ ₂ == Figure 2 A single phase VSC
Refer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?
Three phase Bridge rectifier operated from a 380V, 50Hz source throughout three-phase Y/Y connected transformer with ration 2:1. The load current has continuous character with negligible ripples and average thyristor current of 15A. The circuit inductance per phase is 1.2mH. The rectified voltage due to overlapping angle is 90 % of that voltage when this angle is neglected. 1- How much will the voltage drop be due to circuit inductance * 2- How much will the dc average voltage Vdc(alpha) be. 3- How much will the firing angle be ? 4- The overlapping angle. 5- How much is the percentage change of the output dc power if the thyristors T2, T4 and T6 are replaced by three diodes D2, D4, D6. 6- How much will be the maximum RMS phase current for the mentioned in previous task circuit ( semi-converter). 7- If an additional of 1 mH inductances are added to the existing inductances in the phases , how much will the overlapping angle be. The dc load current is kept constant & the…
Given the center-tap fullwave rectifier circuit shown 220V 60Hz (+2) 220V:Es1-0-Es2 Es1 E$2 D1 D2 RL The transformer is rated 220V:12V-0-12V (Es1=Es2=12V) and the average current through the load RL is 400mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Power dissipated by the load RL. (c) Average current and PIV of each diode.
please explain in detail how to arrive at these answers. I am not the best at using Kirchoff voltage law.