Electrical Engineering-Electrical apparatus 14. A power transformer rated 50,000 kVA;34.5/13.8kV is connected wye-wye.What are the line currents in amperes at full load? Draw the transformer primaryand secondary diagram

For 3 phase transformer, Output in VA = sqrt(3)× Line voltage × Line current. We will use above…

Answered: 14. A power transformer rated 50,000…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Similar questions

Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
Given : 240 /120 V , 10 KVA transformer r1=0.130 , r2= 0.030 , x1= 0.20, x2= 0.050 Find: The full load copper los using a.primary terms and b.secondary terms
74. The eddy-current loss in a 6.9 kV, 50 Hz transformer is 220 W. What will be the eddy-current loss of this transformer if it is to be connected across a 6.6 kV, 60 Hz source? A. 201 W C. 234 W B. 224 W D. 212 W
6. The figure below shows a single-line-diagram of part of a power system. For each transformer in the diagram state a suitable connection method, giving reasons for your suggested connection method. G1 G1 800MW 200MW 15kV 10kV T1-T4 88 T5-T6 250MVA each 125MVA each 330/15kV 88/10kV Line 1 Line 2 T7-T8 100MVA each 330/88kV T9 T10-T11 50MVA 50MVA each 88/66kV 88/11kV T12 2MVA 11/0.4kV Singe-phase loads
A single-phase, 240 kVA, 240/4800 V transformer has the parameters shown in Figure Q5. Determine I and V at the primary and secondary when transformer is operating at full load kVA, 0.8 power factor leading and 220 V at the primary side. Find the voltage regulation. Use actual values and per unit system. 0.002625 Q 0.009 0 1.05 Ω 3.6 Ω V2 40 0 30 Q Figure Q5
Q10) For the transformer shown in Figure below, determine (i) The turns ratio of the transformer (ii) The secondary current (iii) The voltage across the load R = 10k2 (iv) The voltage across the primary winding Ip = 3A Is = ? Ns = 20 turns RL Np = 60 turns 10k2 ellle lelll
Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent circuit elements are: As follows R1 = 0.1 02 x1 = 0.2 2 R2 = 0.25 2 X2 = 0.75 2 RO = 500 XO = 150 Q and feeds a load of 90 kVA at a voltage of 2000 volts and a power factor of 8.0 in delay. Calculate voltage and current Primary Royl ww JX eql
A deita wye transformer connection is shown in schematic form in Figure 2, This transformer is a step- down arrangement from 4.2kV, line-line, to 480V, line-ine, both RMS. See Figure 3. The resistor on the wye side is drawing 100 A. b Figure 2 Transformer Hookup iba b. lac Fizune 3: Single-Phve Loaded Trafoer Connecetion a) How much power is being drawn on the wye side from each of the three transformer secondaries? b) What is the turn's ratio between the physical transformers that make up the three-phase transformer bank? c) What are the three currents in the primary side of each of the three transformers? Show them in a reasonably proportioned vector diagram. Show the voltages as well across those transformer windings. Now the situation is reversed asshowninFigure4. This, too, is a 4.2kV (line-line, RMS) to 480 V transformer, but this time the wye side is on the high voltage and the delta is on the low voltage. A single resistor, drawing 100 A, is connected across two of the…
Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent circuit elements are as follows R1=0.10 x1=0.20 R2= 0.250 X2 = 0.75 RO = 500 XO = 150 It feeds a 90 kVA load at a voltage of 2000 volts and a power factor of 8.0 delayed. Calculate the initial voltage and current? V₁ Regl JXcql Mmm 1₁=1'₂ V'. d Z₁ - Ac Ga
9. Three single phase transformers are used to transform 3 phase power. The primary winding of each transformer has 500 turns and the secondary has 75 turns. The primary windings are connected to a line voltage of 2.3kV. What is the secondary line voltage if the transformers are connected a) primary in wye secondary in delta? b) primary in delta and secondary in wye? c) open delta?

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

14. A power transformer rated 50,000 kVA; 34.5/13.8kV is connected wye-wye. What are the line currentsin amperes at fullload? Draw thetransformer primary and secondary diagram