14. Horsepowerproduced if engineis 4 stroke type andhas 2 cylinders15. Mean EffectivePRessure A. An air standard Diesel cycle rejects 10 KJ per cycle of heat while operating at 300 rpm. At thebeginning of compression, pressure is 98 KPaa and temperature = 30 deg C, volume is 0.046 cu.meter. At the beginning of heat addition, pressure is 3500 KPaa. Determine the following in theTable below (fill up this sheet with your answers, or write a summary of your answers and showyour solution in separate sheets):Item1. PV and TS diagrams2.PVT values at eachpoint in the cycle,see Table below.3. Compression ratio4. Cut-off ratio5. Expansion ratioPVPressure(Koaa)Temp (deg K)Volume(CLM)12.851.57Answer8.171983030.04623500841.61TS335001324.80Unit4184.96571.870.00358 0.00563 0.046

Given: The heat rejected, Qr = 10 kJ The engine speed, N = 300 rpm and the data given is,

Answered: 14. Horsepower produced if engine is 4…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

03/ A 4 cylinder has a following data Bore-15 cm; Piston speed 510 m/min; B.P= 60 kW; T0.80; Pa-5 bar; C.V=40000KJ/kg. Calculate i) whether this is 2 Stroke or 4 Stroke engine and why? 04/ Write a notes on heat balance sheet, draw that on the energy flow and enhance your answers with equations.
Question: Please compute the compression ratio of an engine that has a bore of 5 inches and a stroke of 5 inches when the volume at the combustion chamber is 16.36 cubic. in. with the piston at TDC. Please provide a complete solution. Thak you!
Solve for an engine's Break Mean Effective Pressure (BMEP) if output is 450 hp, 2300 rpm, bore and stroke are 5.5 inches each and with 9 cylinders.
03/ A 4 cylinder has a following data Bore=15 cm; Piston speed 510 m/min; B.P= 60 kW; sch=0.80; P=5 bar; C.V-40000KJ/kg. Calculate i) whether this is 2 Stroke engine and why? or 4 Stroke
QUestion: Please compute the bmep of an engine when the output is 450 hp, 2300 rpm, bore and stroke are each 5.5 in, and with 9 cylinders. Please provide a complete solution. Thank you!
Compute the horsepower output of the following described engine operating at 2000 rpm, bore 3.5 in., stroke 4.0 in., 6 cylinders, and 140 psi bmep. 81.634 hp 29.70 hp 103.94 hp 40.817 hp Other:
A 4-cylinder engine with a bore to stroke ratio of 10 cm x 12 cm, and an individual clearance volume of 120 turns at 2000 rpm. What is the total engine displacement? a. 4523.89 cc b. 942.48 cc c. 3769.9 cc d. 1130.97 cc e. None of the choices Show solution. Please answer honestly and do not just guess. Thank you :)
03 A 4 cylinder has a following data Bore=15 cm; Piston speed =510 m/min; B.P= 60 kW; Nnech=0.80; P=5 bar: C.V=40000KJ/kg. Calculate i) whether engine and why? this is 2 Stroke or 4 Stroke
6. A four stroke 4L Spark Ignition V8 engine runs at 4000 rpm. The compression ratio is 10. The engine is square with bore equals to stroke. Determine the following a. Cylinder bore and stroke b. Average piston speed c. Clearance volume per cylinder
03/ A 4 cylinder has a following data Bore-15 cm; Piston speed =510 m/min; B.P 60 kW; c=0.80; P-S bar; C.V=400O0KJ/kg. Calculate i) whether this is 2 Stroke or engine and why? 4 Stroke
2. Design a cast iron trunk type piston for a single acting four stroke engine developing 75 kW per cylinder when running at 600 r.p.m. The other avialable data is as follows: Maximum gas pressure = 4.8 N/mm2; Indicated mean effective pressure = 0.65 N/mm?; Mechanical efficiency = 95%; Radius of crank = 110 mm; Fuel consumption = 0.3 kg/BP/hr; Calorific value of fuel (higher) = 44 x 10°KJ/kg; Difference of temperatures at the centre and edges of the piston head = 200°C; Allowable stress for the material of the piston = 33.5 MPa; Allowable stress for the material of the piston rings and gudgeon pin = 80 MPa; Allowable bearing pressure on the piston barrel = 0.4 N/mm2 and allowable bearing pressure on the gudgeon pin = 17 N/mm2.
Q.) A six-cylinder diesel engine has the following performance details: 1) work done during expansion = 900kW. 2) work done during suction= 70 kW, 3) work losses due to friction=220 kW. If the brake mean effective pressure is 0.8 MPa. Determine the bore and stroke of the engine taking the ratio bore to stroke equal to 1 and engine specd as 1200 rpm.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

14. Horsepower produced if engine is 4 stroke type and has 2 cylinders 15. Mean Effective PRessure