16. The figure below shows three different arrangements of materials 1, 2, form a wall. The thermal conductivities of the materials are described by: k > k2 > kg. The left side of the wall is 20°C warmer than the right side. Rank the wall arrangements according to: (a) the rate of energy conduction through the wall and (b) the temperature difference across material 1. Rank from greatest to least. 3 to 1 3 1 1 3. 2. 3. 2)

16. The figure below shows three different arrangements of materials 1, 2, form a wall. The thermal conductivities of the materials are described by: k > k2 > kg. The left side of the wall is 20°C warmer than the right side. Rank the wall arrangements according to: (a) the rate of energy conduction through the wall and (b) the temperature difference across material 1. Rank from greatest to least. 3 to 1 3 1 1 3. 2. 3. 2)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter4: Numerical Analysis Of Heat Conduction

Section: Chapter Questions

Problem 4.12P

See similar textbooks

Similar questions

1.3 A furnace wall is to be constructed of brick having standard dimensions of Two kinds of material are available. One has a maximum usable temperature of 1040°C and a thermal conductivity of 1.7 W/(m K), and the other has a maximum temperature limit of 870°C and a thermal conductivity of 0.85 W/(m K). The bricks have the same cost and are laid in any manner, but we wish to design the most economical wall for a furnace with a temperature of 1040°C on the hot side and 200°C on the cold side. If the maximum amount of heat transfer permissible is 950 , determine the most economical arrangement using the available bricks.
1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
A plane wall of thickness 2L has internal heat sources whose strength varies according to qG=qocos(ax) Where qo is the heat generated per unit volume at the center of the wall (x=0) and a is a constant. If both sides of the wall are maintained at a constant temperature of Tw, derive an expression for the total heat loss from the wall per unit surface area.
As a designer working for a major electric appliance manufacturer, you are required to estimate the amount of fiberglass insulation packing (k = 0.035 W/m K) that is needed for a kitchen oven shown in the figure below. The fiberglass layer is to be sandwiched between a 2-mm-thick aluminum cladding plate on the outside and a 5-mm-thick stainless steel plate on the inside that forms the core of the oven. The insulation thickness is such that the outside cladding temperature does not exceed 40C when the temperature at the inside surface of the oven is 300C. Also, the air temperature in the kitchen varies from 15Cto33C, and the average heat transfer coefficient between the outer surface of the oven and air is estimated to be 12.0W/m2K. Determine the thickness of the fiberglass insulation that is required for these conditions. What would be the outer surface temperature when the inside surface of the oven is at 475C?
Q1. Consider the composite materials shown in figure. 1. Sketch the equivalent thermal resistance. 2. Calculate the heat transfer per unit area of the wall. 3. Determine the temperatures at interface between the layers. Material A k (W/m K) 2.1 B 6.7 C 3.5 T-15 °C C B C 195 1/4 14h-10 W/m² K -T=50 °C HATH 320.0020 30 mm -
A team of students tests a material for its thermal conductivity (k). After 20 minutes in a heat box, the temperature is 48° C inside the box and 28° C on top of the material. The following data is true about this test: Area of material = .0225 m2 Thickness of material = .0127 m Light bulb = 25 W What is the thermal conductivity constant for the material? Calculate the amount of energy transferred through the material. Determine the R-value of the material. Based on your calculations, would the material be a reasonable choice for home insulation? Yes of No
A wall is constructed using bricks made of 3 different materials (A, B, C) as shown in the figure (all dimensions are in cm). The depth of the wall is ( w = 20 ), The pattern repeats itself every 20 cm distance in the vertical direction. Thermal conductivities of the materials are given as kA=0.5W/mK, kB=1 and kC=0.35. Inside and outside temperatures are 20 oC and 45 oC, respectively. Considering only convection inside (h=10 W/m2K) and both convection (h=25 W/m2K) and radiation (h=20 W/m2K) outside: w (m) = ? (a) Draw the thermal resistance network (b) Total thermal resistance (c) Total heat transfer rate from the repeated section (d) Temperature Tx
A wall of a house is made from two layers of bricks enclosing a layer of insulation. A radiator is positioned to cover the whole internal surface, and used intermittently when the internal temperature is low. The external surface is exposed to the outside air. Which of the following assumptions could be used to identify the relevant reduced form of the conduction equation to find the temperature in the wall. a. Conduction is mainly in two directions. b. Conduction is mainly in one direction. c. The wall properties are homogeneous. d. Steady conditions exist. e. Unsteady conditions exist. f. There is an internal volumetric heat generation in the wall.
A metal rod 1 sq. in. in cross section and 6 in. long is heated at one end and cooled at the other. If the rate of heat input is 3 BTu/hr and the difference in temperature of the two ends is 2 deg. F, what is the coefficient of thermal conductivity in BTU/(hr)(ft²)(⁰F/ft)?
Two bars A and B, each of length 2m and cross sectional area 1m^2, are placed end to end. Their thermal conductivities are kA = 339 W/mK and kB = 837 W/mK . The left end of bar A is maintained at 373 K while the right end of B is maintained at 273 K. What is the temperature at the interface between A and B?
A mechanic needs to remove a tight fitting pin of material A from a hole in a block made of material B. The machinist heats both the pin and the block to the same high temperature and removes the pin easily. What statement relates the coefficient of thermal expansion of material A to that of material B?
%^0 |. دردشة هندسة النفط/مسائي A composite wall consisting of five series layers of materials with different properties. Layer thickness, thermal conductivity of the layers and temperatures are shown on the figure. Based on Fourier's law for conduction, answer the following questions. 1. What are the main assumptions? 2. Drive an equation to calculate the heat transfer rate through the Composite wall? 3. Draw the themal circuit through composite wall? 4. What are the value Ti? 5. What are the value Tj? 6. What are the value Tr? Givens: KA = 2 W/m. °C K= 1 W/m.°C K= 5 W/m. °C Kp= 4 W/m, °C 100°C Ti 25°C Tj Tr A B D -2cm e 6 cm 4 cm 4cm إضافة وصف...