= 19 mm is 1.7-1 An angle bracket having thickness t attached to the flange of a column by two 16 mm diame- ter bolts (see figure). A uniformly distributed load from a floor joist acts on the top face of the bracket with a pres- sure p 1.9 MPa. The top face of the bracket has length L = 200 mm and width b = 75 mm. = Determine the average bearing pressure of between the angle bracket and the bolts and the average shear stress in the bolts. (Disregard friction between the bracket and the column.) aver τ Angle bracket

= 19 mm is 1.7-1 An angle bracket having thickness t attached to the flange of a column by two 16 mm diame- ter bolts (see figure). A uniformly distributed load from a floor joist acts on the top face of the bracket with a pres- sure p 1.9 MPa. The top face of the bracket has length L = 200 mm and width b = 75 mm. = Determine the average bearing pressure of between the angle bracket and the bolts and the average shear stress in the bolts. (Disregard friction between the bracket and the column.) aver τ Angle bracket

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. A 7/8-in.-diameter steel rod AB fitted to a round hole near end C of the wooden member CD. A shearing stress of 144 psi acts on the surfaces indicated by the dashed lines. 1 in. 1500 lb 750 lb 4 in. D A 750 lb C Determine the maximum normal stress (in psi) in the wood. * Your answer Determine the distance b (in inches) for which the shearing stress is applied. Round off to a whole number. Your answer
... 7.5 mm SN kN SN kN 12 mm 12 mm 7.5 mm 12.5 mm SN kN SN kN 18 mm 25 mm 18 mm On the above figure, determine the following: 1. Maximum bearing stress at joints ( bolts and plates). 2. Shearing stress If the bolts is in double shear. 3. Maximum average normal stress on the plates. Nota: Dound offE vOur anCwer in twe dacimal placar
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
The plate shown in the figure is fastened to the fixed member by three 10 mm diameter rivets. Compute thevalue of the loads P so that the shearing stress of any rivet does not exceed 70 Mpa. SHOW COMPLETE SOLUTIONS DRAW FBD
10 rivets are fastened on a lap joint of 1.25 inch in diameter the thickness of the lap join were measured at 0.85 inch. find the maximum load that can be applied if the allowable stresses were 24 ksi for bearing in the plate and 18 ksi for the shear in each rivet. Friction between plates 1/3 the applied.
Determine the shear Load that act on the fillet weld that joining two plates together if the working stress is 11300 Ib/in? Throat
A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
If the force P reached 10 kN, the wooden specimen shown failed in bearing along a surface. Calculate for the average bearing stress along thementioned surface at the time of failure. P' 16 mm Steel 16 mm 90 mm 15 mm Wood P
ZAO O "l zain IQ YA docs.google.com/forms 10/.. find the shear stress in bolts 2 3 1. 5 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 110 MPa. 127 MPa. 509 MPa no one 0/10 find the tensile stress in upper plate in section 1-1 (2 (5 (3 1 4) + ...
A bracket has been loaded as shown in figure. Compute the top and bottom fibre stress at section A-B
hinz 1. For the beam cross section below, determine the amount of steel As required to cause the strain in the tension steel & to be 0.005 just as the maximum strain in the concrete reaches 0.003. fc' = 3000 psi and fy = 60,000 psi. N.A. b= 10"- Cross Section d = 23" [7422 4233 134 S THE THE CALE DES 2 23-c me Like phans 0.005 PANE Strain 0.003 P HOME st 0.85f Stress 6 I.C. Nc NT * * * * * Delorme
For each of the problems, draw: section + strain profile + stress profile + resultants. Follow sample below. N CONCRETE f 4aoopet GENE Go STEEL Ig. b. 12,423i From ELNTIC BENDING STeEss FORNULA S. - Mce : fI,• 44.6 t-wip G CRACKING MOMENT 0,4 0,000s 3605 K 12,423 in VOLUME OF 30 COMPRESSE TRESSES C- (c) h. 2 T.c (CRACKINA) STRAINS STRESSES RESULTANTS sertion G CRACKING o. Me