19. Two single phase generators operating in parallel have no-loads emfs of E₁ = 24020° V and E₂ = 240/10° V and respective synchronous reactance of Xs1 =j2.5 ohms and Xs2 = j3.1 ohms. Resistances are neglected. The common load is purely resistance of 10 ohms. Find the common terminal voltage in volts. d. 232.65 V d. 6.05, 17.8 A d. 4,985 W a. 236.98 V 20. Referring to problem 19, find a. 6, 17.9 A 21. Referring to problem 19, find a. 4,464 W b. 234.76 V c. 240 V the current of each generator in amperes b. 5.82, 18 A c. 6.34, 17.5 A the total power in watts b. 5,792 W c. 5,616 W

19. Two single phase generators operating in parallel have no-loads emfs of E₁ = 24020° V and E₂ = 240/10° V and respective synchronous reactance of Xs1 =j2.5 ohms and Xs2 = j3.1 ohms. Resistances are neglected. The common load is purely resistance of 10 ohms. Find the common terminal voltage in volts. d. 232.65 V d. 6.05, 17.8 A d. 4,985 W a. 236.98 V 20. Referring to problem 19, find a. 6, 17.9 A 21. Referring to problem 19, find a. 4,464 W b. 234.76 V c. 240 V the current of each generator in amperes b. 5.82, 18 A c. 6.34, 17.5 A the total power in watts b. 5,792 W c. 5,616 W

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are the conditions in paralleling of these DC Generators:a. Shuntb. Seriesc. Compound
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following:a. Circulating currentb. Voltage across the resistorc. Voltage across the capacitord. Real power supplied by the source
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
The section bus-bars A and B are linked by a bus-bar reactor rated at 6000 kVA with 12% reactance. On bus-bar-A, there are two generators each of 10 MVA with 8% reactance and on bus-bar-B, two generators each of 6000 kVA with 10% reactance. Find the steady MVA fed into a dead short circuit all phases on B with bus-bar reactor in the circuit.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
Q9. What is the basic principle that a cage winding can be represented by a three-phase winding? Give your explanation.
The terminal voltage of a 150 kW series generator is 600 V at rated load. The armature resistance is 0.06 ohms and the series field resistance is 0.04 ohms. Find generated emf.
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%
The primary of a certain transformer takes 1 A at a power factor of 0.4 when connected across a 230 V, 50 Hz supply and the secondary is on open circuit. The number of turns on the primary is twice that on the secondary. A load taking 50 A at a lagging power factor of 0.8 is now connected across the secondary. Sketch, and explain briefly, the phasor diagram for this condition, neglecting voltage drops in the transformer. What is now the value of the primary current?
In a Three-phase alternator, a given field current produces an armature current of 250 A on short-circuit and a generated e.m.f. of 1500 V on open-circuit. Calculate the terminal p.d. when a load of 250 A at 6.6 kV and 0.8 p.f. lagging is switched off. Calculate also the regulation of the alternator at the given load. Subject: Electrical engineering
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
TWO transformers A and B are connected in parallel to a load of (2+j1.5) ohm. Their impedances in secondary terms are Za = (0.15+j0.8) ohm amd Zb = (0.1+j0.6)ohm, thier no load terminal voltage are Ea = 200 (angle 0 degree) and Eb = 210(angle 0 degree). Find the power output and power factor of each transformer