For the piston shown below how much should the force applied at the lever to keep it in equilibrium if the load has a mass of 75kg20 cm1mpivot7 mloadoil (s = 0.85)FIGURE O

Answered: 1m 20 cm pivot 7 m load

Engineering

Mechanical Engineering

1m 20 cm pivot 7 m load

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If F1 = 390 N force is applied to the piston with d1 = 4 cm diameter, what is the magnitude of the force F2 that can be resisted by the piston with d2 = 10 cm diameter? Neglect the weights of the pistons.
The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
The below shows an asrag arrangement of objects 7igure in equlibrium. The Block A has a weight of 40.0N, blbck B has weight 07 SO.ON Ppe in the centre, Te, is horizantal and ☺ = 35° q. Calulate tensian I T3 A
Given values: m1 = 10kg, r1=75 cm, m3=20kg, r3=25cm, m4=5kg, had to find the value of r4=? I got r4=50cm m1 = 10 kg at r1 = 75cm m3 = 20 kg at r3 = 25cm m4 = 5 kg at r4 = 50cm 1. Compute the theoretical value of r3 using the following equation: r1m1 = r3m3 + r4m4 2. Compute the % error of r3 using the following equation: % error = |theoretical value - experimental value| / theoretical value x 100%
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.
Find the axial force in BC (in units of kN). The mass of the box is 900 kg. (Make sure to include a negative sign if it is in compression.) 13 m 40° L 12 m 12 m 5 m 13 m
tv wil The following forces are acting on the bracket below. The bracket has a width w of 2 inches and a height h of 3 inches. The bracket is in equilibrium (not accelerating). Determine F3y knowing F1x-98 lbf and F1y-166 lbf. For this question, what is F3y in Ibf? Note that the y-direction is pointing up, so if the force is pushing down on the bracket, it has a negative magnitude. h 3,
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
The figure below shows a painting hanging from a nail fixed into the wall. The picture is supported by a strong, light string attached to the picture symmetrically at two points along the top of the frame. 0.1 m 420 42 05 m 0.75 m Draw a free-body diagram of the painting. If the tension in the string is 60 N, what is the weight of the painting? A person tries to move the painting to the right by pushing on the bottom left edge with a force of 10 N. What moment does this exert about the nail? What force would the person need to apply to the top left edge instead to exert the same moment?
-2- 6.Drand the mechanical circuit for the rolakionale mechamel szolem. b1 Find the drano for fervehen B (moter) el Find B,ls) eesponse if Tom, is shep fone from.
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=250 N. The distance between the points A and B where the cables are attached to the leg is given as L=100 cm and the angle of the leg with the horizontal is γ=6°. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=40°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
Determine the required length of cord AC in Fig. 3-8a so that the 8-kg lamp can be suspended in the position shown. The undeformed length of spring AB is l'AB= 0.4 m, and the spring has a stiffness of KAB 300 N/m. - إحسب الطول المطلوب للحبل (AC) اللازم لتعليق مصباح كتلته (kg 8) كما في الشكل ، علما ان الطول الاصلي m 824.0 C (KAB = 300 N/m) di Jales (0.4 m) (AB) i 2 m KAB = 300 N/m 30° B