2 A water-pipe (A) within a closed chamber is connected to a mercury manometer and a water manometer is connected to the chamber as shown in the figure-2. Determine the absolute pressure (kPa) in the water-pipe (A) if the atmospheric temperature is 27° C and pressure is 1.1 bar. (Given that g = 9.81 m/s²) Take the last three digits of your student ID as a mercury column height (X mm) and take the last two digits of your student ID as a water column height (XX mm). (For Example: If your Student ID is 218362568, last 3 digits = 568, X=568 mm last 2 digits = 68, XX=68 mm) 100 cm Air PHg = 13600 kg/m³ Atmospheric Air (27° C) PH₂0= 1000 kg/m³ XX mm

2 A water-pipe (A) within a closed chamber is connected to a mercury manometer and a water manometer is connected to the chamber as shown in the figure-2. Determine the absolute pressure (kPa) in the water-pipe (A) if the atmospheric temperature is 27° C and pressure is 1.1 bar. (Given that g = 9.81 m/s²) Take the last three digits of your student ID as a mercury column height (X mm) and take the last two digits of your student ID as a water column height (XX mm). (For Example: If your Student ID is 218362568, last 3 digits = 568, X=568 mm last 2 digits = 68, XX=68 mm) 100 cm Air PHg = 13600 kg/m³ Atmospheric Air (27° C) PH₂0= 1000 kg/m³ XX mm

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter13: Energy And Power

Section: Chapter Questions

Problem 22P

See similar textbooks

Similar questions

A cylindrical tank is filled with dimethylformamide (DMF,SG=0.944) up to a height of 3.75 ft. The tank is open to the atmosphere and has a diameter of 4.00 feet. An open end mercury manometer is attached to the side of the tank. Assume the atmospheric pressure is 1 atm and specific gravity of mercury is 13.6. d) Supposing the distance d1 is equal to 0.5 ft, what reading would you expect on the manometer, h (in mmHg)?
(c) Venturi-type flowmeter shown in Figure 5 is used to obtain the flowrate of oil inside a conduit. The diameter of the venturi, d is one third of the pipe diameter, D. The pipe diameter D is 6 cm, pressure difference reading AP, is 25 kPa, discharge coefficient Ca, is 0.98, Bis the ratio of venturi diameter to pipe diameter and oil specific gravity, SG is 0.95. i) Calculate the volume flowrate of oil inside the conduit. ii) Determine the mass flowrate of oil inside the conduit. iii) Explain why the discharge coefficient Ca, for the ventury meter is higher compared to the nozzle meter. 2(P – P.) V. ventury AP oil d Figure 5
A gasoline line is connected to a pressure gauge through a double U-shaped manometer, as shown from Figure 1. a) If the gauge pressure reading is 370 kPa, determine the gauge pressure of the gasoline (kPa). b) If the gauge pressure reading is 240 kPa, determine the gauge pressure of the gasoline (kPa). c) Indicate the pressure difference between the measured pressure and the calculated pressure. Assumptions: 1 - All liquids are incompressible. 2 - The effect of the air column on the pressure is insignificant. Properties: The specific gravities (GE) or also called the relative density (DR) of the oil, mercury and gasoline are 0.79; 13.6 and 0.70; respectively. Consider the density of water ρH O = 1000 kg/m and gravity as g = 9.81 m/s². Tip: Starting with the pressure indicated by the pressure gauge and moving along the tube adding (as we go down) or subtracting (as we go up) the ρgh terms until we get to the tube of gasoline, and set the result equal to P .
A closed pressurized tank shown below is filled with oil and mercury. Mercury is confined inan internal reservoir inside the closed tank, the height of mercury is 450mm. An openmanometer is placed on the bottom left part of the tank with liquid “X” as its gage liquid , thedeflection from the gage liquid shows 800mm. Determine the following:a) Height of the oil from point A up to point c if height A to C is 5 times the height of y.b) Pressure at point B in kPa. c) Pressure at point C in psi.
Tutorial #1 Fluid Properties 1. What is the specific gravity of kerosene, which has a specific weight of 7.853103 N/m?? 2. Two capillary tubes are placed vertically in an open container of water. One tube has a diameter of 2.0 mm, and the other a diameter of 1.0 inch. In which tube will the water rise higher? 3. A sliding plate viscometer, as shown below, is used to measure the viscosity of a fluid. The plate area is 0.75 ft?. A force of 1.531024 lb moves the upper plate at a velocity of 10.0 ft/s. What is the absolute viscosity? - v = 10.0 ft/s 0.50" Fluid 4. A liquid has an absolute viscosity of 2.231025 Ib-s/ft?. It weighs 45 lb/ft³. What is its kinematic viscosity? 5. A liquid has an absolute viscosity of 2.431023 N-s/m?. It weighs 7.853103 N/m³. What is its kinematic viscosity?
3. A differential manometer is attached to two tanks, as shown in figure. A) Calculate the difference in pressure of the two chamber B) Calculate the absolute pressure at A if the chamber B is open to atmos phere C) Calculate the pressure at the interface of the oil and mercury if the pressure at point A is 45 kPa Chamber A 1.1 m oil sg=0.89 0.30 m mercury Chamber B B tetrachloride sg= 1.59 0.8 m
A differential manometer has a reading of 4 in. of mercury when it is attached to a 6 inch diameter pipe as shown. the liquid flowing on the pipe is oil having a sp. gr. of 0.91. Compute the difference in pressure between A and B in psi
3. A combined separating and wire-drawing calorimeter was used to measure the dryness fraction of steam supplied to a steam engine. The following observations were made: Pressure of steam in steam pipe Temperature of steam inside the wire-drawing calorimeter 110 deg C Pressure of steam inside the wire-drawing calorimeter 136mm of water Barometer reading Steam used by the steam engine Water collected in the separating calorimeter Steam condensed on leaving the wire-drawing calorimeter 7bar 750mm of mercury 55kg 1kg 6.5kg
Atmospheric pressure at this location is 102.0 kPa and fluid temperature is presently 30°C. Oil (sg = 0.90) C Water 125 mm 475 mm 250 JU mm 50 mm Mercury (sg = 13.54) Figure 1: Compound manometer (note: sg = specific gravity)
2, Calculation question (80’) (1) Consider a mercury manometer connected to a tank of water, as shown in the diagram below. Please calculate the ratio of hm to hw. (The specific gravity of mercury=13.56) Water Mercury
A pipe contains an oil sp.gr. 0.80. A differential manometer connected at the two points A and B of the pipe shows a difference of mercury as 20 cm. Find the difference of pressure between the two points
calculate the pressure to be read in the (1) manometer in the visible appendix system. The relative distinctive mass of the oil is 0.75 and the relative distinctive mass of the mercury is 13.6.