2- In the circuit below, the initial energy is stored on the capasitor is Vo=16V formerly. Find voltage Vµ(t) using time domain operations. Describe and comment on everything you did. (Aşağıdaki devrede, kapasitör üzerinde önceden depolanmış ilk enerji Vo=16V olarak veriliyor. Vµ(t) gerilimini zaman bölgesi işlemleri ile bulunuz. Yaptığınız her işlemi açıklayınız ve yorumlayınız) 600 V 60 Q 800 V t = 0 t= 0 125 µF 60 + Vo - 150 A Vi(t) 120 Q 640 mH

2- In the circuit below, the initial energy is stored on the capasitor is Vo=16V formerly. Find voltage Vµ(t) using time domain operations. Describe and comment on everything you did. (Aşağıdaki devrede, kapasitör üzerinde önceden depolanmış ilk enerji Vo=16V olarak veriliyor. Vµ(t) gerilimini zaman bölgesi işlemleri ile bulunuz. Yaptığınız her işlemi açıklayınız ve yorumlayınız) 600 V 60 Q 800 V t = 0 t= 0 125 µF 60 + Vo - 150 A Vi(t) 120 Q 640 mH

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 2PA: You are working in an industrial plant. You have been instructed to double the capacitance connected...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load d. a signal light
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
5. Suppose the following circuit is left open for a long time. 5000 22 24 V (a) What is the facial curren What is the carte II What is the ches What is the not the pos 80mF when we close thei 90s after we close the switch? dissipe the resistor 90s arter ene capacitor ons after we close the suit Close the switchi difference across the spacitor 008 after we close the switch across the resisto we close the swit 12 the potential (g) What is the energy stored in the capacitor 90s after we close the switch? (h) What is the energy dissipated by the resistor during the first 90s since the switch is closed?
this is electric circuit questin ...plz solve it early .plz solve early
10 mH jok a resistor, capacitar eard inductor measure the resistoane R using Use to an ohm metere Measure the time constants for the two circuits below and find values of C and L I need help vith the building of this. circuit. 1f you could make them ánd find ans wer to the question abore, I would the C appretiate it gieatly
Q1 Explain the following terms: (a) Sensor (1.5 marks) (b) Transducer (1.5 marks) (c) Instrument Q2 Q3 (2 marks) Based on Figure Q2, if the RTD sensor measurement is 57°C answer the following. (a) Calculate the output current from RTD sensor if the output range is 4 20mA. (2 marks) (b) Calculate the output voltage from the temperature controller if the output range is 0-10VDC. (2 marks) (c) Propose a type of sensor if the process temperature is increased to 1000°C. (1 marks) A capacitive displacement transducer is designed to determine the rotary position. from 0° 180° as shown in Figure Q3. The moving plate whose radius is 40mm is sandwiched between two fixed plates, spacing at Imm. The dielectric constant of air is k 1.The capacitive transducer is formulated as: where; (a) kA€。 farads k = dielectric constant A the area of the plate, in square meters €₁ = 8.854 × 10-12 in farads per meter d = the plate spacing in meters Construct an equation of the change of the capacitance (F) when…
Original Schematic and OrCAD Schematic: The input primary voltage is 250V, frequency 50 Hz, primary inductance setting is 2000H and secondary inductance is 10H and voltage peak to peak ripple is approximately equal to 92mv. U1 D4 IN our DINA002 C3 DIN002 90u R1 R2 10k TXI BC540A V1 VOFF =0 VAMPL 2 FREQ- 50 AC0 XFRM_LINICT-SEC D5 DIN4002 C2 0.384m 84 5 HH
Convert the circuit from a T to a pi configuration
1)The value of the capacitance reactive power in VAR is? /2) The value of the capacitor in micro farad is?
cedb-e70a-017569bcae60/ecam kderi - Go OI Wallpaper Abyss-- Istanbul Online Ye. 8 am 1A MASTERCHEF A. 0 Shefodk 2 Seon 2 la 4. Questerar In the circuit in the figure emf of the battery& = 20 V. %3D All the inductors are of the same inductance, L=0.05 H and of negligible resistances. Resistances of the resistors are Ro = 30, R = 10, R, = 4, R = 49, Rg = 40, Rg = 50, 42, R = 49, R, = 40, Rg = 50, %3D %3D %3D R = 30. The switch S is closed at the time t = 0. %3D What is the current flowing in Ro long after the switch S is closed? ЗА 8A 0 2.5A 4A 11 ituwitwises.io ekraninızi ve sesini paylaşyar. Paylaymayr durdur Gole 17 ト

Determine the fime rece soary for the incducfor current to decay to are -fourth of its value at t=0. 24 V (* Uce tha oditor to format