2 m 2 m B D 1.5 m E C Draw the free-body diagram of the entire assembly and member ACE. P.

Q: H.W. Determine the horizontal and vertical components of force at pins A and D. D Ans: A = 24.0 kN…

A:

Q: A 120-kg horizontal beam is supported at the ends A and B. A 340-kg piano rests a quarter of the way…

A:

Q: 05. The homogeneous 600-lb plate is suspended from three cables. Determine the tension in each…

A:

Q: Q3 \ Determine the horizontal and vertical components of reaction at the pins A, B, of the…

A:

Q: 6 m 5 m 5m 5000 N A, 45° B 6 m

A: For a step-by-step solution have a look through the attached pictures of the solution. The required…

Q: 10 kN 4 kN/m A B 2 m 2 m 2 m

A:

Q: 15KM. B. 6m 3m. Determine the force iñ each member and state Wha thir it is iñ tenrim or…

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN ALL MEMBER

Q: Determine the magnitude of the pin force at A. Assume W = 580 lb, a = 2.9 ft, b = 2.4 ft, r = 8 in.…

A:

Q: H.W. Determine the horizontal and vertical components of force at pins A and D. D Ans: A = 24.0 kN…

A: FBD of pulley E equating force along y axis∑FY =02T-12kn =0T=6Kn

Q: The rig shown consists of a 1350-lb horizontal member ABC and a vertical member DBE welded together…

A: the free body diagram of the rig is given below,

Q: Determine the forces in members BC and BH of the loaded truss. 1400 lb. 25° D 1150 lb. 18 E 22' В…

A:

Q: ~4%3D0.2 BA D 4m Hi =0.2 -7.5 m-

A: To determine the weight of the block D that can support the pole ABC.

Q: Side fogune shows a crate (box) d mass m=200 kg is suspended AB and AC and AD. Je üsibg the ropes…

A:

Q: The member shown is pin-connected at A and rests against a smooth support at B. Determine the…

A:

Q: Determine the forces in members CD, CJ, and DJ. M 9' A L 6' B L 6 panels at 3¹ K C L D L I E L H L F…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 690 lb, a = 2.8 ft, b = 2.1 ft, r = 8 in.…

A:

Q: Q1: Determine the force in each member of the loaded truss. 6m 5 m 5m 5000 N A, 45° B 6m

A:

Q: Determine the force in each cable needed to support the 3500-lb platform. Set d=2 ft Solution: AB…

A: Vectors are defined as mathematical expressions possessing magnitude and direction, which add…

Q: 2. Determine the horizontal and vertical components of reaction at A, B, and C of the three-hinged…

A:

Q: 126 Determine the forces in members CH and CF. -2 m- 2 m- -2 m- -2 m A |C D E 2 m 24 kN I H G 24 kN…

A: Consider point A (To determine the angle) Taken +ve in an upward direction  Taken -ve in a downward…

Q: 4. Determine the force in members NO, KE and KD. N 20 kN – 2 m K M kN 2 m A B C D E F G H 60 kN 60…

A:

Q: 1. Determine the reactions acting on the smooth uniform bar, which has a mass of 20 kg. 4 m 60 30

A:

Q: Determine the forces in members CD, CJ, and DJ. 6 panels at 4' M K J I H E 8' L 5' B L C L D L L L F…

A:

Q: The member shown is pin-connected at A and rests against a smooth support at B. Determine the…

A:

Q: Using the method of joints, determine the force in each member of the truss shown 2000 lb -12 ft→12…

A:

Q: Identify the zero-force members in the truss shown. A 10 000 N 10 000 N 10 000 N (A) GI, HI (B) AB,…

A: Zero force members,reaction in vert members which haven't any internal loading. If at any joint on…

Q: Determine the forces in members CD, CJ, and DJ. M 6' A L B L 6 panels at 3¹ K C L D I E L L H F G L…

A:

Q: P E B C 4 m F G H I 4 tableros @ 3 m= 12 m

A:

Q: Bermine the reaction at AB, C and D. W- 200 kN W 400 kN 1m D 2m 5.6 m

A:

Q: The rig shown consists of a 1450-lb horizontal member ABC and a vertical member DBE welded together…

A:

Q: 300 mm A E -200 mm B 1) W -200 mm- с W

A: To find: The forces in the member ABC. Free body diagram.

Q: The square steel plate has a mass of 1650 kg with mass center at its center G. Calculate the tension…

A:

Q: Q3 Determine the force acting along the axis of each of the three struts needed to support the…

A:

Q: Draw the free body diagram member CD

A: Given data  To draw the FBD of member CD

Q: Determine the horizontal and vertical components of force at pins A and D. D 2 m 0.3 m 15m |B -1.5 m…

A:

Q: 3. Using Method of Sections, Determine the 12 kN force and state if it is in Tension or Compression…

A: to find force in member CG,CJ,CD,GJ

Q: The 375-kg uniform l-beam supports the load shown. Determine the reactions at the supports. +2.0 m-…

A:

Q: e cables are joined at the junction ring C. De- ine the tensions in cables AC and BC caused by…

A:

Q: Deter mine all force members Of the truss Shown 3m bo0 N

A:

Q: 1. Determine the reactions acting on the smooth uniform bar, which has a mass of 20 kg. 4 m 60

A: Given: To determine the reactions acting on the bar.

Q: Determine the force in member GH of the truss shown. 30 k 30 k 30 k 15 k a E F G H 12 ft a 4 at 16…

A: To find: Force in the member GH and the nature of the force in that member.

Q: For the truss shown below determine the internal forces of member BE and AB. 200N 30 50N D 100 N E A…

A:

Q: Determine the magnitude of the pin force at A. Assume W = 675 lb, a = 2.7 ft, b = 2.0 ft, r = 9 in.…

A:

Q: Determine the horizontal and vertical components of force at pins A and D. D 2 m 0.3m A 1.5 m -1.5…

A: Given :-  Determine the horizontal and vertical components of force at pins A and D.

Q: Determine the horizontal and vertical components of reaction at the pin A and the reaction on the…

A:

Q: cise Determine the force developed in the member BC and reactions at the pin support A. Take G, 5Kg.…

A:

Q: |-1.5- -1.5- 2 IB 5 1.5 2.5 A Dimensions in feet Fig. P4.52

A:

Q: Q2: Determine the reactions of fixed support at A 15 kN 15 kN 8 KN/m 4 kN/m 60 3 m 3 m

A:

Q: Determine the magnitude of the pin force at A. Assume W = 825 lb, a = 2.8 ft, b = 2.2 ft, r = 6 in.…

A:

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.