2. A simply supported beam carries a service live load of wll and a service dead load of wdl including its own weight. The beam has a cross-section of 300mm x 600mm with a steel cover of 70mm and reinforced with 4- 25mm diameter bars. If f'c = 28MPa, fy 414MPa, determine whether the beam can safely carry the load. span of beam = 6m wll = number of letters of family name times 10kN/m = wdl= number of letters of family name times 5kN/m

2. A simply supported beam carries a service live load of wll and a service dead load of wdl including its own weight. The beam has a cross-section of 300mm x 600mm with a steel cover of 70mm and reinforced with 4- 25mm diameter bars. If f'c = 28MPa, fy 414MPa, determine whether the beam can safely carry the load. span of beam = 6m wll = number of letters of family name times 10kN/m = wdl= number of letters of family name times 5kN/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported steel joist of 4 m effective span is laterally supported throughout. It carries a total UDL of 40 kN (inclusive of self weight). Design an appropriate section using steel of grade Fe410. The following two beam sections are available ISMB 150 @ 146 N/m ISMB 175 @ 191 N/m b₁ = tf = 8.6 mm t = 5.5 mm bf = 80 mm = 7.6 mm tf t = 4.8 mm 1₂=726.4 x 104 mmª = 96.9 x 103 mm³ 22 Z₂ R₁ Zp = 9 mm = 110.5 x 103 mm³ = 90 mm = 1272 × 104 mm² Izz Z = 145.4 x 10³ mm³ = 10 mm R₁ Z₁ = 166.1 x 10³ mm³
USE NSCP 2010 A rectangular beam reinforced for both tension and compression barshas an area of 1450 mm² for compression bars and 4350 mm² fortension bars. The tension bars and compression bars are placed at a distance of 600 mm and 62.5 mm respectively from the top of thebeam. The beam width 300 mm, fc’ = 21 MPa, fy = 415 MPa andtension steel covering is 60 mm.If it is 8 m-simply-supported beam that carries three concentratedservice live loads P applied at three quarter points of the beam (exceptat the supports), neglecting the self weight of the beam, determine themaximum value of service load P in kiloNewtons.
The beam shown is lateraily braced only at the ends. The 180kN load is a service live load. Use Fy= 345 MPa and determine whether a W310 x 74 is adequate. 180 kN 2.5m Section Properties: d = 310mm tw = 9.40mm Ag= = 9420 mm² lx = 163x106mmª ly = 23.4x105mmª Ho=295mm 2.5m bf = 205mm tf = 16.3 mm J=712x10³mm* Zx = 1.18x10 mm³ Cw=505x10 mm5 rts = 57.2mm
5) Calculate Mer for the beam below: It is simply- supported over a span of' 35 'Feet. t has a 28-day strength of fi= 5500 psL. 34" Aps : 1.53 in? fpu = 270 ksi foy= 243 ksi = 150 ksi b=14" %3D fse
A W420x85 steel beam is fully restrained with a uniformly distributed live load of 25 kN/m. The beam has a span of 10m. Use A36 steel. Properties of W40 x 85 A = 10839 mm2 %D bf = 180 mm tf = 18 mm %3D tw = = 11 mm Ix = 310 x 106 mm4 %3D d = 420 mm (Note: Since this is a built-up section, for checking of web slenderness, use h = d - 2t;) %3D 1) Calculate the design shear strength of the section. Check if the section is adequate in shear. USE LRFD and U = 1.2D + 1.6L. %3D 2) Is the maximum deflection at the midspan of the beam due to live load adequate? 3) Calculate the maximum uniform live load that can be carried by the beam.
A W310 x97 steel wide-flange section Supports a uniformly distributed line load on a simple span of 7 m. Assume A36 steel. Calculate the allowable load (kN/m). Neglect the weight of the beam. Use Fv=0.4 Fy Material Steel ASTM A36 or A501 Steel (high-strength low-alloy) ASTM A992 Steel AISI 1020 hot-rolled Steel AISI 1040 hot-rolled Stainless steel (annealed) Cast iron (gray) Aluminum alloy 6061-T6 Magnesium alloy Titanium alloy Brass (rolled) Bronze (cast) Copper (hard drawn) Concrete Density kg/m³ x 10³ 7.85 7.85 7.85 7.85 7.85 7.21 2.64 1.794 4.40 8.56 8.56 8.81 2.40 Mod. of Mod. of Elasticity E MPa Rigidity G MPa x 10³ x 10³ 207 83 207 207 207 200 103. 70 45 114 97 83 103 21.5 83 79.3 79.3 80 41 28 17 45 41 34 41 Tensile Yield Strength F, MPa 250 345 210 290 280 240 210 900 340 170 280 Ultimate Strength MPa Tens. Comp. 400 450 380 520 580 140 260 280 970 410 230 380 550 390 21 Shear Coeff. of Thermal Expansion m/m/c x 10-6 260 11.7 11.7 11.7 Poisson's Ratio μ 0.25 9.9 0.25 11.7 0.25…
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D
Problem 1: Determine the design strength of a T-Beam giventhe following data: bf= 700 mm bw= 300 mm hf= 100 mm d = 500 mm fc' = 21 MPa fy= 414 MPa As: 5-20 mm dia. Problem 2:Compute the design moment strength of the beam section described below if fy = 420 MPa, fc' = 21 MPa. d= 650 mm d'= 70 mm b = 450 mm As': 3-28mm dia. As: 4-36mm dia
Problem 1. A W30 x 116 beam hasthe top flange restrained againstlateral displacement and rotationand has an unstiffened web. A pointload is applied to the top flange at2m. From the left support. The beamspans 12 m. Use A36 steel with yieldstrength of Fy = 248 Mpa. a. Compute the maximum value of point loadthat may be applied without web yieldingoccurring. b. Compute the maximum value of point loadthat may be applied without web cripplingoccurring. Properties of W30 x 116d = 762 mmK = 41.28 mmbf = 266.7 mmtf = 21.59 mmtw = 14.33 mm
TASK 3 250 180 14 I 30 24 Weld 450 A compound girder consists of a steel joist with steel plates welded onto each flange as shown. If the ends are simply supported and the effective span is 10 m, what is the maximum UDL which can be supported by the girder? [kN/m] Allowable longitudinal stress in plates = 110 MN/m² Allowable load in shear for each weld = 60 kN/m Allowable shearing stress in web of girder = 75 MN/m² Note: 1.0 MN/m² = 1.0 N/mm² 50
Determine the maximum safe service live load that the beam can carry if the service dead load is 10kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40MPA and fy=415MPa. top bars are 6-36mm and bottom bars are 3-36mm, center to center distance between the top bar layers is 108mm. WLL = kN/m 70 mm 108 mm 352 mm 70 mm 300 mm 7.2m 6.7m A В O O
For the hollow beam. Calculate the design. capacity, As = 2040mm ² Fy = 420 Mpa,Fc=25Mpa,Asmin check is not required