2. Calculate Passive House's energy demand.a, Calculate window U-value based on given data in figure.0.117m0.117m0.134mC₂UtotalWglass-0.996m= 1.229mglassUglass = 0.6-glassW window - 123mWm².c0.117m1.48mnwindowWm² °CUframe = 1.6-Area₁ U₁ + Area2 U₂... + Area, * U₁Area totalb. With the calculated U value for the windows find out how much power needed to maintain 20°C in ahome with outside of 0°C based on the following: the house having a square footprint 17 m by 17 m,walls 2.5 m high (Uwalls = 0.152 each of the four walls hosting two windows, and each windowhaving an area of 2 m². The entry door area is 2.5 m² (Udoor = 0.65- ). What are the heat loss ratesfor the installed windows, the door, the walls, the ceiling, and the floor? What is the overall heat loss rateof the home?m². C1. What do these calculated heat loss rate values mean?2. What is the definition of the passive house?3. What does the U-value represent? Use its unit as a hint and describe it with your own worlds.

Given: To find: U value of window Power needed

2. Calculate Passive House's energy demand. a, Calculate window U-value based on given data in figure. 0.117 0.117m 0.134m C. Utotal = 1.229m glass hglass Uglass = 0.6- -0.996 Arame Wwindow123m W m².c 0.117m hwindow *1.48m W m² °C Uframe = 1.6- Area U₁ + Area2 U₂+ Area U₁ Area total W b. With the calculated U value for the windows find out how much power needed to maintain 20°C in a home with outside of 0°C based on the following: the house having a square footprint 17 m by 17 m, walls 2.5 m high (Uwalls = 0.15- 5m² each of the four walls hosting two windows, and each window having an area of 2 m². The entry door area is 2.5 m² (Udoor = 0.65; ). What are the heat loss rates for the installed windows, the door, the walls, the ceiling, and the floor? What is the overall heat loss rate of the home? I W m². C 1. What do these calculated heat loss rate values mean? 2. What is the definition of the passive house? 3. What does the U-value represent? Use its unit as a hint and describe it with your own worlds.

2. Calculate Passive House's energy demand. a, Calculate window U-value based on given data in figure. 0.117 0.117m 0.134m C. Utotal = 1.229m glass hglass Uglass = 0.6- -0.996 Arame Wwindow123m W m².c 0.117m hwindow *1.48m W m² °C Uframe = 1.6- Area U₁ + Area2 U₂+ Area U₁ Area total W b. With the calculated U value for the windows find out how much power needed to maintain 20°C in a home with outside of 0°C based on the following: the house having a square footprint 17 m by 17 m, walls 2.5 m high (Uwalls = 0.15- 5m² each of the four walls hosting two windows, and each window having an area of 2 m². The entry door area is 2.5 m² (Udoor = 0.65; ). What are the heat loss rates for the installed windows, the door, the walls, the ceiling, and the floor? What is the overall heat loss rate of the home? I W m². C 1. What do these calculated heat loss rate values mean? 2. What is the definition of the passive house? 3. What does the U-value represent? Use its unit as a hint and describe it with your own worlds.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Wind power is defined as the use of air flow through wind turbines to provide the mechanical force to generate electricity. Wind power is an alternative to burning fossil fuels, and is renewable and produces no greenhouse gas emissions during operation. Modern horizontal-axis wind turbines often use three blades. Theoretically, the maximum power P (unit: watts) that a three-blade wind turbine can extract from the wind power can be calculated as: P = pAv³C₁. . (Equation 1) where p is the air density (kg/m³), A is the sweep area of the turbine (m²) and can be calculated from the length of the turbine blades, and v is the wind speed (m/s). Cp is the power coefficient that is unique to each turbine type. This coefficient represents the amount of kinetic energy from the wind that is captured by the turbine. From the Betz's limit law we know that the best power conversion possible is Cp,max = 0.59. Part 1 Given the following data: Blade length /= 50 m Air density p= 1.5 kg/m³ Power…
Sheet -2- QI/ Complete the following table for water NO T kpa p m/kg phase V 1 125 0.53 2 1000 Saturated-liquid 4. 25 750 4 500 0.130
A liquid reactant solution is pumped through a pre-heater before entering a reaction vessel. The solution enters the pre-heater at 25 °C and must enter the reactor at 45 °C. The flow of the reactant solution is 1500 mL per minute. The density of the reactant solution is 0.91 g-cm3 and the heat capacity is 1.75 Jg1.K1. ASsume there is no heat loss in the pre-heater or between the pre-heater and the reactor. a. Draw a schematic of the pre-heater, detailing all mass and energy flows. b. Clearly define a system boundary. c. Write the general energy balance, and a simplified energy balance stating all assumptions that apply to this problem. d. What is the minimum power rating required for the pre-heater?
Q1. Find the heat flow rate through the composite wall as shown in Fig. bele Assume one dimensional flow & the area is variable for each layer. Where: 60°C kA = 152 W/m°C, kB = 31 W/m°C, %3D 3 cm kC = 68 W/m°C and 7 cm %3D kD = 53 W/m °C. 400°C A 10 cm 5 cm 8 cm 3 cm D. BC
Q1. Find the heat flow rate through the composite wall as shown in Fig. below. Assume one dimensional flow & the area is variable for each layer. Where: 60°C kA = 152 W/m°C, kB = 31 W/m°C, cm kC = 68 W/m°C and 7 cm D %3D B kD = 53 W/m°C. 400°C 10 cm 5 cm 8 cm
Q1. Find the heat flow rate through the composite wall as shown in Fig. below. Assume one dimensional flow & the area is variable for each layer. Where: kA = 152 W/m°C, kB = 31 W/m°C, kC = 68 W/m°C and → 60°C :3 cm kD = 53 W/m°C. B 17 cm 400°C A 10 cm 5 cm 8 cm cm
A 0.41 m^3 air tank is pressurized to 5.17 MPa. When the temperature reaches -13deg C, calculate the air mass in kg. a.76.3 b.28.4 c.69.3 d.32.0
Q1) Calculate the size of air-conditioning (tons) required to cool a room of 7 m x 4 m x 3.5 m before and after the insulation, which is the polystyrene (EPS). Note that the materials of the walls and the roof are shown in the figures below. Neglect the effect of radiation and convection heat transfer. Add 3500 W to the total load due to the heat gained through windows, ventilation, occupants and equipment. Also, find the percentage reduction. Kplaster=1, Kbrick=0.5, Kgypsum=0.8, Kpolystyrene=0.08, KRC=2, Kconcrete tiles=0.8 Tout = 50 °C Concrete Tiles 10 cm Tin = 24 °C Polystyrene 10 em Tout = 45 °C Reinforced Concrete 20 cm Polystyrene 5 cm Brick Plaster 24 cm Gypsum 1 cm Gypsum 1 em 2 сm Tin = 27 °C Wall section Roof section Ans.: 2.67 TR, 1.53 TR, 43%
Q1: If a calorimeter is not assumed to be adiabatic, how would one calculate the heat transfer? Guide Questions: What are the parameters to be considered and the equations to be used? What law of thermodynamics does this transfer of heat to the surroundings touch? Is an adiabatic system automatically considered as a closed system? Please help me understand by also attaching a reference/book/journal article. This would help me in my essay. Thank you.
An office space of 12 ft x12 ft x10 ft height. The heat loss through roof is (4780.8 Btuh) if Tb.l.=80 F, To= 5 F, and Uroof%3D0.4 Btu/hr.ft2.F * True False
2) Also determine the rate of heat rejection to the surrounding air. A: 2866 W B: 2766 W C: 2666 W D: 2566 W Q6: A balloon behaves so the pressure is * P = CV, C = 100 kPa/m. The balloon is blown up with air from a starting volume of 1.3 m3 to a volume of 3.5 m3. Determine 1) value n is A: Positive B: Negative C: Zero
A certain gas with Cp= 0.529 BTU/lbmole-Rankine and Cv= 0.4053 BTU/lbmole-Rankine expands from 20ft3 and 500 Rankine to 30 ft3 and 1620 Rankine its pressure remains constant at 40lbf/ in2 . R(gas constant)=97.24 ft3 -lbf/lbmole-Rankine Compute: a) Change of internal energy (BTU) b) Change of enthalpy (BTU) c) Heat Transferred (BTU)