2. Design a V-Belt drive, Specify the belt size, the sheaves sizes, the number of belts, theactual output speed, and the center of distance.ServiceInputInput PowerNominalProblemDriverDrivenТурeMachinedayspeedoutput(HP)(kW)(rpm)speed(rpm)17503.733102622V-BeltAC motorFan(NT)

Given: The service day, N = 22 The input speed, ni = 1750 rpm The input power, P = 3.73 kW = 5 hp…

2. Design a V-Belt drive, Specify the belt size, the sheaves sizes, the number of belts, the actual output speed, and the center of distance. Driven Service Input Input Power Nominal Problem Driver output speed (rpm) Туре Machine day (НР) (kW) speed(rpm) 1750 5 3.73 310 26 22 V-Belt AC motor Fan (NT)

2. Design a V-Belt drive, Specify the belt size, the sheaves sizes, the number of belts, the actual output speed, and the center of distance. Driven Service Input Input Power Nominal Problem Driver output speed (rpm) Туре Machine day (НР) (kW) speed(rpm) 1750 5 3.73 310 26 22 V-Belt AC motor Fan (NT)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The BAPCO in Bahrain is looking to design a V belt drive system for its recently installed rotary machines. The smaller pulley having a diameter of * d" is connected to an electric motor and run at a speed of nd. The belt is used to drive a larger pulley at a speed of 90 rpm. The V belt is used to transmits a power of 95 hp and ignore it in belt class selection process (Table 17.9). The service factor for the V belt drive system is 1.3 and the suggested factor of safety for the current design is 2.5. Smaller Pulley Diameter = d = 9 in Speed of smaller pulley = nd = 900 rpm Design and select a V belt drive system.
Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal output speed as 725 rpm. Starting with belt linear velocity 4000 ft/min, specify the input sheeve D1 from the list above. D1 = ___ in. Provide write down steps including equations
Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal output speed as 725 rpm. Starting with belt linear velocity 4000 ft/min, specify the input sheeve D1 from the list above. D1 = ___ in. Provide write down steps including equations. *** 8.73 and 8.9 were marked incorrect
Help me please
TO THE NEXT PROBLEM Design a complete belt drive system for an AC motor (NT) running a fan 12 hrs/day, with an input power 10 hp and input speed of 1000 RPM. The desired output RPM and center distances are 500 RPM and 36 inch, respectively
An Electrical motor (heavy start) that delivers 53,57 kW at 1440 r/min must be connected to a rotary compressor with a wedge belt drive. The compressor must operate 24 hours per day with a shaft speed of approximately 966 r/min. The center distance must be closest to 1000 mm.
What type, size, and a number of classical V-belts is recommended for this system. The motor is rated at 3 Hp, VFD controlled and runs at 1750 rpm under load. The output speed required is 1075 rpm. The application is a saw that cuts wood and the environment is dusty. Target center distance is 18 inches, but 16 to 20 inches is acceptable. Due to clearance constraints, the driven pulley may not be larger than 6 ½ in. The motor will slide to adjust tension.8 hours service per day.
If the peak power of your electric motor occurs at a torque (Tm) of 0.001 Nm and you have a load (FL) of 1.2 Ibf to pull using a motor, gear box, and winch (rw-0.125 inches). What gear ratio would result in the load moving as fast as possible at equilibrium? Tm Motor Gear Tgb W Воx gb F.
Q5: What kinds of Belt drives with explanation only. one
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
3G zain 1Q Asiacell design1.pdf → Н.W Design V-belt drive to the following specifications a Power to be transmitted = 75 kW Speed of the driving wheel (N) = 1440 rpm; Speed of the driven wheel (No) = 400 rpm; Diameter of the driving wheel (d) = 300 mm; Centre distance = 2500 mm Service = 16 hours/day Assume any other relevant data if necessary.
Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage mechanism, calculate instantaneous torque, required to drive the mechanism and to present the results of the case study in a clear reporting format. Introduction: Figure 1 shows a pumpjack operating at an oil well. Its representation as a linkage is also shown in Figure 1. The pumpjack is driven by a motor attached to crank OA. A constant torque T is applied to the crank and the crank rotates at a constant angular velocity ???. A force P is applied vertically downwards at the end of the walking beam BD, which has its centre of mass at point G. To design the mechanism, a careful kinematic analysis of the mechanism needs to be conducted. To avoid mechanical failure and to provide adequate support to the mechanism, the engineer needs to analyse the reaction forces in the joints. Masses of links OA and AB are assumed to be smaller in comparison with the mass of BD and are ignored in the analysis.…