Hello, please solve the problem attached image. Thank you!Using 4 decimal places at final answer. Hint: Ah=33.5...kn, Av=150kn,Bh=-33.5...kn. 2. Determine the member end moments and reactions for the frame shown in the figure byusing moment-distribution method.C30 kN/m-10 mEl= constantD8 m

Answered: 2. Determine the member end moments and…

2. Determine the member end moments and reactions for the frame shown in the figure by using moment-distribution method. A C 30 kN/m -10 m El = constant D 8 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 2. The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. Determine the…

Q: Find the external reactions at support A (fix-end) for the beam shown in the figure. A 7 kN 2 m 3 m-…

Q: A horizontal curve has a radius of 650 ft, measured to the right edge of the rightmost lane. The…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Assume a string with length L which is fixed at left side, and the mass, m, and the stiffness k are…

A: Given:-Length=Lmass=mstiffness-kTo find:-a) governing equations and boundary conditionsb)…

Q: 3. The strut is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter of…

A: Given Data σy = 36 Ksi A-36 steel wire AB. Diameter of wire (d) = 0.2 in. Find stretches in…

Q: 20 kN- 12 kN 12 kN 40 kN- 40 kN- 40 kN- -5 at 3 m- 15 m- 12 kN E M 12 kN N D B 12 kN To 12 kN 4 m 4…

Q: Q3. A plate shown in Figure 3, is submerged in oil (s=0.9) and lies in vertical plane. Find the…

A: Given: Specific gravity of oils=0.9 To find: Magnitude and location of hydrostatic force.

Q: Why is it necessary to modify the gross stiffness values in the structural models? What values…

A: One of the key stages of structural engineering is structural modelling. Basically, a 3D model is…

Q: From the following rocks prepare a list in order of their decreasing unconfined compressive…

A: The utmost compressive stress that a plastic specimen can sustain before rupturing or deforming by a…

Q: A headlight is located 0.6 meter above the PVC. The light beam directs 1 degrees above the…

A: In highway driving, stopping sight distance is defined as the minimum sight distance available at…

Q: A sample of dry soil is coated with a thin layer of paraffin and has mass of 460 g. It displaced 300…

A: Given data- Dry soil sample- Mass of dry soil + mass of paraffin = 460 gm, Mass of paraffin = 9 gm,…

Q: Calculate the horizontal force P on the light 11° wedge necessary to initiate movement of the 43-kg…

A: Given data : Angle of Wedge =11° Weight of Cylinder =43 Kg Coefficient of Static friction = 0.34

Q: The 81-lb force P is applied to the 220-lb crate, which is stationary before the force is applied.…

Q: A vehicle moving at 40km/h speed was stopped by applying brake and the length of the skid mark was…

A: Given data: Speed, u = 40 km/h = 11.111 m/s Length of skid mark, L = 12.2 m Average skid resistance,…

Q: The designer of a ski resort wishes to have a portion of a beginner's slope on which the…

Q: 1. Calculate for the (In terms of El) a.) B b.)ΔΒ d.)AC e.)AD f.) Amax 2.. El= 50000 kN m² A 2 m B…

A: As per company policy we can only answer first question And in multiple parts we can only answer…

Q: Problem 3: The frame system is fixed at A with a roller support at B and a pin at C. Determine 1)…

A: Given : Determine : 1- The reaction at A and B 2 - The internal forces at cross section DDC and…

Q: er of transfer units, and the height of the p ng/L and this must be reduced to 75 µg/L

A: Solution- Lequid loading rate Mass rate Mass rate = 1kg/L×350 gal/min =…

Q: Homework Draw the Axial Force Diagram (NFD), Shear Force Diagram (SFD) and Bending Moment Diagram…

A: its very simple problem so i have not cut the second to draw SFD and also i didn't find the…

Q: Please fill in the blanks of the Column below. Need help!!!!!!!!!!!!!!

Q: Concider a harbour gate 16.8m wide. If the sea faceing side had a depth of 18.11m and produces a…

Q: [2 5 71 The Green strain tensor (E) is 5 2 2 MPa. [725] Determine the three principal invariants…

Q: In traveling a distance of 4.2 km between points A and D, a car is driven at 104 km/h from A to B…

A: "Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Find the external reactions at supports A (roller) and B (hinge) for the beam shown in the figure.…

A: Beam analysis is a method for designing beams that can withstand stresses and stress while using the…

Q: In a rectangular open channel, 2.0 m wide, water flows at a depth of 0.8 m. It discharges over an…

A: Given- Rectangular open channel- Width B=2 m, Depth y=0.8 m, Weir crest depth H=0.25 m, Coefficient…

Q: Definition and derivation of hydraulic force on plane surface Free surface- Centroid, c Location of…

Q: Given a rectangular doubly reinforced beam with b = 14", d = 16", f = 1350 psi, f, = 20,000 psi, and…

Q: Groundwater contaminated with 800 mg/L compound with MW=92.14 g/mole. How many liters/hr of air are…

A: Given Data: The data is given as: Influent compound(Cin)=800mg/Leffluent compound(Cout)=98% of…

Q: etailed explanation about Newton-Raph

Q: A 1.5m long column has a circular cross-section of 50 mm diameter. Consider 1 Rankine's formula with…

A: Given- 1.5 m long column, Diameter of cross-section d=50 mm, Stress fc=560 N/mm2, For pinned ends-…

Q: A) A fully penetrating unconfined well of 12 in. The diameter is pumped at a rate of 1 ft^3/sec. The…

A: As per company policy we can only answer first question. Kindly post other questions as seperate…

Q: write solutions and formulas out clear

A: Given:- base=35mm thick =4mm wall thickness=3mm total height of cup=50mm machine moved at speed of…

Q: Explain Distortion of flat, square, and round pieces as affected by direction of growth rings after…

A: Wood is a material with biological origins that is anisotropic, porous, and inhomogeneous. It is a…

Q: The beam shown in the figure carries two 40-lb forces, a distributed force, and a moment M-260…

Q: The 81-lb force P is applied to the 220-lb crate, which is stationary before the force is applied.…

Q: A vehicle moving at 40km/h speed was stopped by applying brake and the length of the skid mark was…

A: Brake efficiency: The ability of the brake to lower the vehicle's speed to a potential stop, to…

Q: A compound curve is laid out 480 m. from the P.C. to the P.C.C. having a radius of 763.94 m then…

Q: A two-lane highway along the border has a horizontal curve segment with radius of 656 ft (measured…

A: A two-lane highway (separated) along the border has a horizontal curve The radius of the curve = 656…

Q: Given. A shear wall 24 ft. long and in. thick with a floor-to-floor height of It. Compressive…

Q: A one lane loop ramp at the northwest quadrant of an interchange, this loop ramp is for northbound…

A: Given- Friction factor f=0.095, Design speed V=35 mph, Radius R=545 ft,

Q: 5. Two hard rubber blocks are used in an anti-vibration mount to support a small machine as shown in…

A: Given Data : P = 150 lb Downward deflection = 0.25 in. a = 0.5 in., b = 1.0 in. and c = 2.5 in. To…

Q: ENGINEERING MECHANICS

Q: Given the table below, compute the area of the traverse by coordinates method. Traverse 6 A B с D E…

A: Given Data: Traverse 6 X-Coordinate Y-Coordinate A 0.00 0.00 B 20.00 35.00 C 35.00 20.00…

Q: A particle which moves in two-dimensional curvilinear motion has coordinates in millimeters which…

A: Given:- The given equations, x=5.1t2+8.1y=8.2t3+3

Q: Determine the force of all members using METHOD OF JOINT. Answer in 3 decimal places only. TRUSS…

A: Objective: To determine the force of all members of the given truss using the method of joints.…

Q: to perform satisfactorily as road surfacing,bitumen aggregate mixes need to possess certain…

A: According to its definition, bitumen is "a viscous fluid or a solid, mostly composed of hydrocarbons…

Q: Determine the force P required to force the 17° wedge under the 96-kg uniform crate which rests…

Q: The uniform beam has a mass of 57 kg per meter of length. Determine the reactions at the supports. A…

A: Reference : Structural Analysis To determine : Reactions at A and B

Q: The desired characteristic strength of a mix is 20N/mm². The standard deviation is 4 N/mm² for 150…

A: Given data:- The given characteristics strength, fck=20 N/mm2 The given value of K=1.645 The given…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 95 125 95 -170- Dimensions in…

Concept explainers

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.

Question

Hello, please solve the problem attached image. Thank you! Using 4 decimal places at final answer. Hint: Ah=33.5...kn, Av=150kn,Bh=-33.5...kn.

2. Determine the member end moments and reactions for the frame shown in the figure by
using moment-distribution method.
C
30 kN/m
-10 m
El= constant
D
8 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the member end moments and reactions for the frame shown in the figure by using slope-deflection method. 30 kN/m 8 in 10 m El = constant
Calculate the support reactions of the beam and determine the degree of indeterminacy in the figure. q:11
6. Determine the member end moments (BC, CA and CD members) and reactions (B, A, and D) for the frames shown in Figure 6 by using the moment-distribution method. 50KN 50kN/m D B E 2m 200KN 2m A 6m EI= constant E = 70GPa I= 496 x 106 mm 6m 2m
Determine the member end moments and reactions for the frames shown by using the moment-distribution method. 18 kN/m B 100 kN-m 5 m El = constant E = 200 GPa I = 1360(106) mm* A 5 m 5 m
Determine the value of plastic moment for the frame shown in Fig QI. The plastic moment is uniform throughout. 20KNIM B 100Kl mp lom mp mp A Fig. QI
2. Find the centroid of the figure shown below. Also, find the reactions at A and B considering specific weight of y = 0.25 lb/in and thickness t= lin. r= 38 in. 16 in. A 20 in. B
Select all the correct assumptions about the Moment-Distribution Method. 1. The structures have members of constant cross section throughout their respective lengths. That is, the members are prismatic.2. The joints to which members are connected can rotate, but the ends of all members connected to a joint rotate the same amount as the joint. At a joint, there is no rotation of the ends of members relative to each other or to the joint. 3. Axial deformation of members is neglected. 4. The joints at which two or more members frame together do not translate. Excess or insufficient assumptions means wrong.
Figure 1: For the frame shown, determine the magnitude of the pin reaction at B. Neglect the weight of the frame. (2 decimal point, indicate the answer in kN. Ex: 3.87kN just encode 3.78) * 2 m 1.8 m 3 m 15 kN/m A 12 kN/m
Q1 Determine the member end moments and reactions for the frames shown below by using the slope-deflection method. 27 KN- 1432 E 1 C 21 21 10m- E constant 5m 5m
Determine the member end moments and reactions for the frames shown in the figure by using slope deflection method
Determine the member end moments and reactions for the frame shown in figure by using following methods a) Approximate method of analysis: Portal method b) Exact method of analysis: Moment distribution method (20 + 2y) kN – 21 (4 +0.1y) m (50 + 2y) kN – 21 D (4 + 0.1y) m 10 m E and A = constant Here y = 4|
If you know that the line of influence of the reaction force of the joint of the serration in the figure below lies along the member A To bring the truss into equilibrium under the action of force B, find its amount and the reaction of the joint CA .C at a point NΚ10 in vertical