2. From Figure2, calculate the current I, in the following circuit using nodal analysis.3k2V221,3V6k22k2Figure 2

The above circuit can be solved using either of the circuit theory rules mentioned below:…

Answered: 2. From Figure2, calculate the current…

Engineering

Electrical Engineering

2. From Figure2, calculate the current l, in the following circuit using nodal analysis. 3k2 V2 21 3V 6kN 2k2 Figure 2

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Related questions

Q: Q2) Using mesh analysis to determine the current through the 6v- battery for the circuit shown in…

Q: R1 680 N IN R2 R3 B 3.3 k2 1.5 k2 R4 RL 2.2 kn 15 V 820 N D Figure 6.12

Q: Solve the following problem:

A: According to Kirchhoff's current law (KCL), the sum of the total current entering or leaving a node…

Q: 9) Using mesh analysis, determine the current through the 8-V battery for the circuit shown in…

A: In this question we need to find a current through 8 V battery.

Q: 2. Find V1, V2, 1,l2, 13 & I4 in the following circuit using voltage and current division rules. I,…

A: Let the equivalent resistance be Req

Q: Q2. Find out the total resistance of the given below circuit? 242 102 152 V1 +

A: to find the total resistance for the given circuit

Q: I . 13 V R1 R2 R3 R4 10 V 470 ohm 680 ohm 820 ohm 1.0 kohm Figure 4.1: DC Parallel Circuit Given the…

Q: Determine practically the current through 10K2 in circuit below using Thevenin's theorem R2 1.2 kn…

A: In this question, we have to find out current through 10 kilo ohm using thevenin theorem...

Q: a) For the network shown in the below figure, the value of current needs to be measured in the 10002…

Q: Q2) Using mesh analysis, determine the current through the 52 resistor Then determine the voltage V.…

A: The circuit seems to be non-planar, but after rearranging the 3 ohms resistor the circuit becomes…

Q: R2 10 ka R1 10 ka 12 R3 V2 5V V1 MESH 1 10 V 1 ka MESH 2 A. Determine current 12, across the…

A: A.determine current I2 in terms ofI1,R2,R3 B.current I1,I2

Q: Solve i and v for each resistor using i. Combination Circuit ii. Mesh Analysis iii. Nodal…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: QQ Using nodal analysis, find current i, and the power dissipated in the 4-ohm resistor in the…

A: Here we applied the nodal analysis at V1 and V. We are assumed the node voltages such as V1 and V .…

Q: Calculate the current through each passive element of the circuit network in Figure Q2(a) using: (i)…

A: KCL (Kirchhoff's Current Law) states that the algebraic sum of current at node or junction is zero.…

Q: Find the voltage, current and power values of R3 resistor using Thevenin's Equivalent Theorem for…

Q: Practice problem 3.1: Find the voltages at the three nonreference nodes in the circuit of Figure…

A: Nodal analysis uses Kirchhoff's current law and ohm's law. Let us denote the node voltage as…

Q: 8. Determine the mesh currents in the circuit below. Ix 20 102 100 + 3Vx 4lx 10V 수 5V

A: The solution can be achieved as follows.

Q: Q3- For the network of Figure 3: a. Find IDQ. b. Determine VDQ and VDSQ. c. Find the power supplied…

Q: 4. Determine the voltages @ nodes “1" and “2" and the branch currents in figure C using Nodal…

A: In this question we will find node voltages and currents...

Q: 4) Solve for i, 3 k2 1 ΚΩ ip Ava Va > 2 k2 6 v (+

Q: (a) Determine the node voltages for the circuit shown. (b) Calculate the current through the…

Q: ·Study the following circuit diagram 12V R1 R2 R3 R4 ere would be a decrease in the current through…

Q: QUESTION 4 Solve the voltage V, across R (300) resistor by using the mesh-current analysis in Figure…

Q: 12 Ohm Q3/ For the circuit shown find 24 Ohm 6 Ohm 24 Ohm The current through 6 N by Using thevnin…

Q: R1 R2 R3 R4 V2 2.5 V 2ka 10kn 20kn 100kn 2.5 V Figure 3: Circuit 3 Referring to Figure 3, use…

Q: 12 V 2i 20 ww Figure 2

Q: In the circuit shown below, apply KCL to find the value of i when v = 2. The -(Q2) .resistor values…

Q: Q2) If VRI = 3 V, VR2 1 V, VR3= 4000 mV, VR4 = 6 V, VLampl=4 V for the circuit in figure 2, apply…

A: The given close circuit consists of the four resistances, a lamp and a source. The value of the…

Q: 2VA R1 R2 VA Vs Is + R1=10kn, R2=7kO Vs=1,8V, Is = 9,7mA. Find the the Maximum power transfer (Pmax)…

Q: In the network shown in Figure Q3(a), two independent voltage sources act on the elements in the…

A: We will apply KCL to find out current . First we will find out the current due to individual source…

Q: Tor the circuit shown in the figure, R1 445 k), R2 IMO, and V 30 V. V is measured with voltmeter…

Q: Q1: Find the Norton equivalent circuit for the following circuit with respect to the terminals ab. 2…

A: Norton theorem states that any linear network with multiple number of sources and multiple…

Q: The network shown in Figure 1.33 consists of a collection of resistors, batteries, and cur- rent…

A: This question comes under circuit theory . It is based on source transformation technique . Current…

Q: Q2) For the network of Figure below, determine: a. IB. b. Ic. c. VE. d. VCE- 18 V 6 ka 250 ka VCE…

Q: Find V, in the network in Figure 3 using Nodal Analysis (Hint: Note that the circuit contains two…

Q: For the circuit shown below: (a) Find the voltage Vo in the circuit shown below. (b) Calculate the…

A: We will use KCL, KVL and current division rule to find unknown voltage and power delivered by…

Q: Q2) Using mesh analysis, determine the current through the 52 resistor Then determine the voltage…

Q: 1 k2 ww I, 2V

A: Thevenin's theorem states that a linear and bidirectional two terminal networks can be replaced by…

Q: 2. Complete the table of values for this circuit: (show your solutions) R = 330 2 Rg=470 Ω R, = 820…

Q: (a) Calculate the Thévenin equivalent circuit between terminals a and b for the circuit shown in…

Q: Q2) A- Find the Number of Nodes, Branches and loops for the following circuit: 2 kQ 6 kQ 8 kN 8 k2 3…

Q: 30 Q ww 20 V 10 Q 80 V

A: A mesh is defined at a loop which does not contain any other loops within it. To apply mesh…

Q: (b) Using mesh analysis find i₁, 2 and is in the circuit in Figure 3. 552 20 V + i 12 V 252 12 692…

Q: Practice Problem Obtain the node voltages in the circuit 2 ww ЗА 70 O 12 A Answer: v, = -6 V, v2 =…

Q: 2.1- Determine the voltages V1, V2, V3 and V` for the circuit shown. RI 2kn 45 V R2 5Ka V2 R3 8Ka

Q: A, - 120 n R 120 1.2 ka 5.1 kn h.) current through R4 if R2 and R3 opens i.) Power dissipated by R1…

Q: Practice problem 3.1: Find the voltages at the three nonreference nodes in the circuit of Figure…

A: We need to find out node voltage for given circuit

Q: Q/ For the circuit shown in the figure below, determine the current (1)Using : 1- (Mesh current) for…

Q: a) Use the superposition method to find the voltage Vo in the DC circuit shown in Figure 3. b)…

Q: R1 a 6Ω b V1 R2 R3 I1 .For the circuit shown above, find the Thevenin voltage looking into the a-b…

Concept explainers

Nodal Analysis

In the analysis of any electric circuit, nodal analysis is the method of determining the potential difference or voltage between different nodes in an electric circuit. A node is a point where two or more branches connect each other. In the nodal analysis, the voltages are determined in the terms of branch currents. The nodal analysis is also known as the node voltage method or branch current method. The nodal analysis method is one of the several applications of Kirchhoff's Current Law (KCL).

Question

2. From Figure2, calculate the current I, in the following circuit using nodal analysis.
3k2
V2
21,
3V
6k2
2k2
Figure 2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Using NODAL VOLTAGE ANALYSIS, solve Vy and Vx and voltages across EACH RESISTOR. Put signs on each resistors in the figure and draw the flow of current
the adjoining figure. This lamp can withstand a maximum voltage 3.0 v 0.4 9. Volt-ampere (V-I) charaeteristics of an incandescent lamp 16thd in and a maximum current 0.4 A. An infinite ladder network consisting a large number of these lamps is also shown in the figure given belo How much maximum voltage can be applied between the terminals A and B, so that no lamp gets damaged? (Use V5 = 2.2). Ans:x4.2V Hint: Curentin all bulls except first is
What is the difference between the cut-off voltage VGS0 f and the narrowing voltage Vp? Explain this with the diagram
Given the circuit below and that R1=1.7ohm,R2=3.5ohm,Emf1=2.1V and Emf2=6.3V. What is the current through the section ac?
A dc generator and a battery are connected to a resistive load RL in the figure below. For each, determine the value of RL for maximum power transfer to RL. Next is to determine RL to 75% efficiency
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
3Draw the circuit diagram an solve using ohms law asap pls 3. Two lamps rated 100W and 200V areconnected in series across 200V supply . Find the power consumed by each lamp
Shown in the figure below is an electrical circuit containing three resistors and two batteries. I₁ 0= 4 + L . ww R3 R₂ ww 1₂ R₁ ww Write down the Kirchhoff Junction equation and solve it for I, in terms of I₂ and I3. Write the result here: 1₁ = 12-13 R₂=552 R₂ = 132 13 Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and follows the perimeter of the circuit diagram clockwise. - IzR3 − LR₁ + 14 + 10 Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and touches the components 4V, R₂, and R₁. 0 = 4-1₂R₂-11R₁ The resistors in the circuit have the following values: R₁ = 12 Solve for all the following (some answers may be negative): I₁ = 27.78 X Amperes 1₂ = 28.84 X Amperes 13 = 1.060 X Amperes NOTE: For the equations, put in resistances and currents SYMBOLICALLY using variables like R₁,R₂,R3 and 11,12,13. Use numerical values of 10 and 4 for the voltages.
A 5-ohm resistance is connected in parallel with a 10- ohm resistance. Another set, a 6-ohm and 8-ohm resistances are also in parallel. The two sets are connected in series. - - - Draw the circuit, find the equivalent resistance, total current, and the voltage across each resistor.
I am very confused with this problem, I know that I have to reduce the circuit, and we will end up with 2 resistor 1 in each side and the current in the middle, I know that I have to use current division, how do I know according to this problem which Z1 and Z2 will be. The io is on the right side.. The io will be the same in the left and right side... I need steps for this problem please
The diagram in the figure shows a simple circuit consisting of a battery and a load consisting of two resistors.The battery voltage is UB = 56 V and the value of the resistors is:R1 = 1800R2 = 5400a) The ammeters in the circuit show the following value:A1 shows valueA2 shows valueA3 shows valueb) In the load, the effect developsc) The total resistance of the load is
Kirchhoffs Law find all the currents through the resistors in milli Amperes and the voltage drops across all the resistors. Steps: a) redraw the circuit with the voltages and currents labeled for each of the respective resistors. b)solve