2. Select the lightest W8 section that will resist a service tensile load D=100k and L=140k. The member is to be 24 ft long and is assumed to have two lines of holes in each flange and one line of holes in the web. Assume there are four bolts in each line 3 in on center. All holes are for 7/8-in bolts. Use A992-grade 50 steel.

2. Select the lightest W8 section that will resist a service tensile load D=100k and L=140k. The member is to be 24 ft long and is assumed to have two lines of holes in each flange and one line of holes in the web. Assume there are four bolts in each line 3 in on center. All holes are for 7/8-in bolts. Use A992-grade 50 steel.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.6.3P

See similar textbooks

Similar questions

The tension member shown in figure below is a PL ½ x 8 of A36 steel. The member is connected to a gusset plane with 1 ⅛ inch-diameter bolts. It is subjected to the dead and live loads shown. Does this member have enought strength? Assume that Ae=An. a. Use LRFD b. Use ASD
The tension member shown is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. Tühitinin 2" 2" + 32 | 3² | O O O O OO O
4. An UPE 300 is to be used as a tension member and it is bolted to a 10mm thick gusset plate with bearing type 8-M20 8.8 bolts as shown in the figure below. a. Check all spacing and edge distance requirements. b. Compute the allowable tensile strength of the channel UPE 300. Don't consider shear strength of the bolts and bearing strength of the bolt holes. [all dimensions are in mm] Material both for gusset plate and UPE 300: S275 F-275N/mm² Fu=430N/mm² UPE 300 Ag = 5660 mm² tw 9.5 mm x = 28.9 mm 70 160 70 + 10mm thick gusset plate +50+ 80 -80-80-50 o +50+80 -80 80-50 UPE 300
Check the bolted section of the given gusset plate connection assuming that the connection is done by M12 bolts with a staggered arrangement. The maximum design tensile axial force to be sustained is Ned = 168 kN. Assume a grade of S235 steel. P. Gusset plate BỘ do=13mm Gusset plate O DO t=16mm t-16mm1 Ni.Ed FO NtEd do=13mm do3D13mm G. 40mm 40mm 140 mm 240mm 30mm
Determine the allowable tensile force P which can be appllied to the plates shown. The AISC specifications A36 steel and 20 mm diameter A325 bolts placed in standard holes with threads excluded from the shear plane are used in a bearing in a bearing type connection. Fy = 248 MPa, Fu = 400 MPa, Fv = 206.9 MPa and Fp = 1.5 Fu. P P CIVIZ 12mm 250 mm ENGINEERING - STEEL DESIGN 12mm P P
At the connection at point C, 4 M20 bolts are used to connect the U150x75x6.5x10 profile with the gusset plate, tb = 10 mm. The quality of U profile steel and gusset plate is BJ41. Bolt quality is A490M with shear plane on the non-threaded part. a) Check the bolt clearance requirements in the direction of the force. b) Check that the shear strength of the bolt is sufficient to withstand the factored load SUBC. c) Determine the distance between the bolts, s, so that the bearing strength of the connected plates is sufficient to withstand the factored load SUBC. Baut M20 - S, BC U150x75x6,5x10 Pelat buhul, t = 10 mm Kolom WF 300x300x10x15 (satuan dalam mm) 81
Problem 3 An equal-leg angle L8x8x5/8 tension member is subjected to tensile loads. The connection between the member and the gusset plate is made by using 4-1 1/8" diameter bolts in one row as shown. Assume Fy = 36 ksi and Fu = 58 ksi. Use U = 0.8. Determine the controlling design tensile strength OPn of the tension member (the smallest OPn from yielding, rupture, and block shear) 1¾" 2½" 3 spaces @2½" L 8x8x5/8 1 1/8" diameter bolts
A double-channel shape, 2C8 x 18.75 is used as a tension member. The channels are bolted to a ¾-inch gusset plate with % - inch diameter bolts. The tension member is A572 grade 50 steel and the gusset plate is A36. If LRFD is used, how much factored tensile load can be applied? Consider all limit states. →2" popoy |-|-|-|-|-| n оо- 0 0 0 0 x + = ³/8" 288×18.15
The 10mm x 400mm plate has a steel grade of A36. The diameter of the bolt is 22 mm. The tensionmember shown has a length of 6 m. If the said tension member is carrying a tensile dead load of 698kN and a tension live load of 668 kN, determine the following:a. Effective areab. Is the member satisfactory? Use LRFD and ASD.
Compute the design strength (øPn) of the double angle tension member shown below for the following limit states: • tensile yielding in the gross section • tensile rupture in the net section • block shear rupture Identify the controlling limit state. Note: • The angles conform to ASTM A36 • LLBB = long legs back-to-back PL I" 11 (6) 7/B DIA. BOLTS z" 3" 2" -2L6x4x%2 LL BB
1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts. The steel is A36. Compute the following: 130 mm 25 mm 0 0 a) The design strength for LFRD. b) The allowable strength for ASD. 25 mm CIVIL ENGINEERING STEEL DESIGN
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127