2. Two gaseous streams enter a mixing chamber through two sections and leaves through one section. Entrance conditions are: A₁ = 450 cm2, ₁ = 150 m/s, v₁ = 0.625 m³/kg and A₂ = 380 cm², ₂ = 55 m/s, P₁ = 2 kg/m³. At the exit conditions are: 3 = 245 m/s and v3 = 0.58 m³/kg. Determine the area of the exit section.

2. Two gaseous streams enter a mixing chamber through two sections and leaves through one section. Entrance conditions are: A₁ = 450 cm2, ₁ = 150 m/s, v₁ = 0.625 m³/kg and A₂ = 380 cm², ₂ = 55 m/s, P₁ = 2 kg/m³. At the exit conditions are: 3 = 245 m/s and v3 = 0.58 m³/kg. Determine the area of the exit section.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(4) A water hose connected to a nozzle is used to fill a 10 L container. The internal diameter of the hose is 2 cm and the nozzle exit has an inner diameter of 1.7 cm. It takes 30 s to fill up the container. If the inlet pressure is 2 atm and the nozzle exit is 0.8 m above the hosea. What is the velocity (m/s) of water at the outlet stream and at the inlet stream?b. What is the water pressure (atm) at the outlet stream c. What is the mass flow rate of water (kg/s)?
At inlet to a certain nozzle the specific enthalpy of the fluid passing 3500 kJ/kg and the velocity is 70 m/sec. At the discharge the specific enthalpy is 2782 kJ/kg. The the nozzle is Horizontal and there is negligible heat loss from it. (a) find the velocity at exit from the nozzle (b) if the inlet area is 0.1 m^2 and specific volume at inlet is 0.198 m^3/kg, find the mass flow rate (c) if the specific volume at the nozzle exit is 0.598 m^3/kg, find the exit area of the nozzle
3. In figure shown, pipes 1 and 2 are of diameter 3 cm, D3 = 4 cm. Alcohol (SG = 0.80) enters section 1 at 6 m/s while water enters at section 2 at 10 m/s. Assuming ideal mixing of incompressible fluids, compute the exit velocity and density of the mixture at section 3. The temperature is 20°C. Answer: 9 m/s, 928 kg/m3 (2) Ideal mixing (3) V₂-P3
Towards the inside of a cylindrical tank with diameter: D = 24 m, water flows through a tube 1 with a velocity v1 = 20 m / s and exits through tubes 2 and 3 with velocities v2 = 8 m / s and v3 = 10 m / s respectively. At 4 there is a vent valve open to the air from the atmosphere. (a) What is the speed with which the level rises of water in the tank? (b) what is the average velocity of the air flow at valve 4? assuming air is incompressible. Assume the following pipe diameters: D1 = 3 m, D2 = 2 m, D3 = 2.5 m, D4 = 2 m, consider that the density of water is: ρw = 103 kg / m3 , and the density of air is: ρa = 1.2 kg / m3
Water is pumped up to 8 m height. The pump operates in steady state, and it is perfectly insulated. Pressure increase over the pump is 850 kPa. The velocity of the water at the pump inlet w is 1 m/s and at the outlet w₂7 m/s. The diameter of the inlet d' is 0.12 m. The water is saturated at the inlet, and the temperature Tis 18 °C. The density of the water is assumed to be constant. The efficiency of the pump n is 77.0 %. Reduce the equation for energy balance with the given assumptions, and calculate the power of the pump and the fraction of kinetic energy. 0 = P + + qmh₂ h₁ + Read from h,s-chart Specific volume of inlet water v Power of pump P 2 w² - w² 2 The share of kinetic energy of the total pump power -2₁)) + g(²₂ — Z₁)
Refrigerant R-134a enters a 30cm diameter pipe (circular cross-section) at an absolute pressure of 200 kPa and a temperature of 10 °C with a velocity of 5 m/sec. Heat is transferred to the refrigerant as it flows and the gas leaves the pipe at 180 kPa and 50 °C. Find the following quantities:a. The volume flow rate at the exit in m3 /sec.b. The exit velocity in m/sec.
Water (modeled as an incompressible substance) flows steadily through a circular pipe oftotal length ? = 10 m. The mass flow rate through the pipe is ?̇ = 2 kg s⁄ and the watertemperature drops by 25°C as it moves through the pipe. Pressure losses within the pipeare negligible, as are any changes in potential and kinetic energy of the flowing fluid.a) Determine the rate of energy loss from the water as it moves through the pipe. Youmay treat the water as having a constant specific heat (? = 4.18 kJ kg-K⁄ ). Recall thatfor an incompressible substance Δℎ = Δ? + ?Δ?, where Δ? = ∫ ? ?? and ? is thespecific volume of the substance. Your solution should start with an energy balanceon an appropriately defined system/control volume.b) The air surrounding the pipe is at ?∞ = 25°C and the convection coefficient at theouter surface of the pipe is ℎ = 15 W m2-K⁄ . It is also known that the surfaceemissivity of the pipe is ? = 0.3 and the walls of the room where the pipe is locatedare at ?sur =…
In the jet impact experiment, water jet impacts on a curved vane in the vertical direction. As shown in the figure below, the exit has an angle with respect to the vertical direction. The distance from the nozzle to the vane surface at the exit is h. The water volume flow rate is measured to be Q, the density of water is p, and the cross section area of the nozzle is A₁. Assume that the flow has reached the steady state. (1) Use the Bernoulli's equation to determine the velocity Vout at the exit of the vane. Assume that friction between water and the curved vane can be neglected. (2) Apply the Reynolds transport theorem to derive the expression of the impact force F, on the curved vane (neglect the jet weight). (3) Under the condition of a fixed volume flow rate Q, determine the maximum impact force Fr,max that can be obtained when the angle varies (e.g. in different vane designs). Va out 9 Ao Vout h
Hot water at a constant volumetric flow rate of Fh and temperature Th(t) is mixed with cold water at a constant volumetric flow rate of Fc and a constant temperature of Tc. Both streams flow into a bathtub, but because of carelessness, the water is overflowing and keeping the bathtub full of water. The bathtub volume is V, and the heat loss can be ignored. Assuming the water in the bathtub is perfectly mixed and constant density and heat capacity, derive the differential equation relating the temperature in the bathtub, T(t), to the temperature of the hot water, Th(t).
Water flows through a horizontal coil heated by steam condenaing on the outside. If the inlet pressure and temperatire are 2 atm and 160°F (state 1) and at the exit 1 atm and 220 °F (state 2), calculate the heat added to the coil per pound mass of water. The entering velocity is 5 ft/s, and the leaving, 500 ft/s. Data: H1=127.9 Btu/lb, H2=1154.4 Btu/lbA. 1031 Btu/lbB. 1042 Btu/lbC. 1048 Btu/lbD. 1052 Btu/lb
The inlet pressure to a piping system is 440 kPa. The inlet pipe diameter is 0.6 m. What is the velocity of the flow of water and discharge at the inlet?
NEED IMMEDIATELY. 1)Determine the mass flow rate in lbm/s of a liquid (ρ = 0.8 g/cm3) flowing through a 2 in (inside diameter) pipe at 480 m/min. A horizontal pipe of cross section 1.5 in2 has a constriction of cross section of 2 cm2. Gasoline flows in the larger pipe with a speed of 500 m/hr. Find the speed in the constriction in ft/min. SHOW COMPLETE SOLUTION and conversion