2.4) Recommend design parameters of an AM standard broadcast receiver that is to operate with an intermediate frequency (IF) of 455 kHz, thus A) Calculate the required frequency for the local oscillator fLo when the receiver is tuned to fc = 540 kHz, assuming that frequency of the local oscillator is above the frequency of the received signal.

2.4) Recommend design parameters of an AM standard broadcast receiver that is to operate with an intermediate frequency (IF) of 455 kHz, thus A) Calculate the required frequency for the local oscillator fLo when the receiver is tuned to fc = 540 kHz, assuming that frequency of the local oscillator is above the frequency of the received signal.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write the functions of (i) Repeater and (ii) Receiver. For an amplitude modulated wave, the maximum amplitude is 15 V and the minimum amplitude is 3 V. Calculate the modulation index.
(vi) Find the local oscillator frequency. (vii) Determine the image frequency rejection in dB.
The figure below shows the frequency spectrum of an AM signal. 15V 6V 6V 475kHz 480kHz 483kHz 488kHz a) Draw the frequency spectrum of the modulating signal and label completely b) Calculate the effective voltage of the AM signal c) What is the percent modulation?
FM Demodulator Circuit Design I need an FM demodulator circuit for Frequency Modulated Sound Signal with 127MHz carrier frequency. I need clear mathematical steps for element value calculations. Thanks in advance.
How to calculate the efficiency in frequency modulation and what is the highest value for efficiency in frequency modulation
Determine four distinct types of modulation processes.
To modulate a pulse carrier with sinusoidal signal to obtain a Pulse Position Communication system lab. Experiment 3: Pulse position Modulation Department of EME Object: Modulated signal. EQUIPMENT: 1. Experimental training board. 2. Oscilloscope. lab THEORY: The amplitude and width of the pulses is kept constant in this system, while the position of each pulse is varied by each instantaneous sampled value of the modulating wave. Pulse Position Modulation(PPM) has the advantage of requiring constant transmitter power output, but the disadvantage of depending on transmitter receiver synchronization. PROCETURE: 1. Connect the CRO probe to the socket marketed TP2,the wave form should be a sinusoidal as shown in fig.2(a). 2. Now move the CRO probe from TP2 and connect it to TP1.the waveform here should resemble that of fig.2(b)i.e., a pulse train(carrier). 3. Connect TP1 to input terminal & TP2 to input terminals and switch on the main supply. Observe the waveform on the CRO at TP3.…
Please answer numbers 3 AND 4 ONLY asap with clear and complete explanation. Thank you! Electromagnetics (Communication Receivers) 1. what is communication receiver and explain in detail the operation. 2. Explain in detail how the design of dual-conversion receivers allow them to enhance selectivity and eliminate image problem. 3. Explain the relationship between(IF) local oscillator, and signal-frequencies mathematically and calculate any one of them, given the other two. 4.What is mixer circuits and explain in detail.
Draw a block diagram of a PM demodulator using frequency discriminator method.
Explain what is modulation?
5. A superheterodyne receiver is tuned to a station at 3.7 MHz. The IF frequency of the receiver is 10.7 MHz. Assume that the local oscillator operates at a frequency above both the station and the IF: a. What is the local oscillator frequency? b. If the local oscillator produces a second harmonic, what two additional frequencies will be received?
Derive the effect of phase and frequency errors between the local oscillator signal and the received SSB carrier signal in the synchronous SSB detector.