24/ The resistance and standstill reactance of each phase of a 3-phase induction motor with star- connected rotor are 0.062 and 0.42 respectively. The full-load slip is 4%. Calculate the resistance per phase of a star-connected rheostat which when connected to the rotor will give a pull out torque at one-half of full-load speed. What is then power factor? Ans[0.1482 , 0.707Lag]

24/ The resistance and standstill reactance of each phase of a 3-phase induction motor with star- connected rotor are 0.062 and 0.42 respectively. The full-load slip is 4%. Calculate the resistance per phase of a star-connected rheostat which when connected to the rotor will give a pull out torque at one-half of full-load speed. What is then power factor? Ans[0.1482 , 0.707Lag]

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
An 8 pole, 50 Hz slip ring induction motor runs at a slip of 2.67% on full load. The rotor resistance per phase of the winding is 0.2 ohm. What external resistance per phase must be added in the rotor circuit so that the motor now runs ate a slip of 17.33% such that the torque remains same in both the cases. (Ans: 1.1 ohm)
Design and develop equivalent circuit model of a single phase Induction motor with th consideration of core losses present with the parameter consideration of stator resistance R1 and reactance X1 and two rotor parameters which includes r2,x2 and magnetising reactance xm. (Illustration is required) Draw by hand please
A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
2. Describe the Torque-Slip characteristics of a three phase induction motor.
A 3-phase, 50-Hz induction motor with its rotor star-connected gives 500-V(r.m.s.) at standstill between the slip-rings on open-circuit. Calculate the current and power factor at standstill when the rotor winding is joined to a star-connected external circuit, each phase of which has a resistance of 10 Q and an inductance of 0.04 H. The resistance per phase of the winding is 0.2 Q and its inductance is 0.04 H. Also, calculate the current and power factor when the slip-rings are short-circuited and the motor is running with a slip of 5 per cent. Assume flux remain constant.
• Q5/ in a DC motor. List and describe the types of losses that occur
A value of magnetizing current in a 3-phase induction motor * gives power factor smaller .. larger smaller. .poor large . better O large...poor O
A 110 V, 60 Hz, 6 – pole single phase induction motor 1/3 hp has the following equivalent circuit impedances: RI = 1.52 ohm, R2 = 3.13 ohm and x1 =2.10 ohm, x2 =1.56 ohm. Xm=58.2 ohm, The Friction, windage and stry losses =16W, the core loss = 35 W, For a slip of 0.05, calculation (a) input current, (b) power factor, (c) developed power, (d) output power, (e) speed (f) in put power (g) air gab power (h) T ind (i) T load 6) efficiency.
An induction motor having full load torque of 60 Nm when delta-connected develops a starting torque of 120 Nm. For the same supply voltage, if motor is changed to star -connection, then starting torque developed will be Nm.
B/ Fill in the blanks: TV ezur 1- In a three-phase induction motor iron losses in stator will be..... that in rotor. 2- In three-phase induction motors sometimes copper bars are placed deep in the rotor to........... 3- Blocked rotor test on induction motors is used to find out. R..., ke, X. 4- The maximum torque in an induction motor depends on .............and .....