Answer as many as you can, no solution needed 24. A 3/8 in wire rope is made of plow steel having a tensile strength of 240 ksi. For it to have an infinite life,the pressure strength ratio should be 1.4 x 10-³. If the allowable fatigue tension for the rope is 800 lb,determine the minimum diameter of the sheave in inches.1415a. 12b. 1326. Determine the torque required to accelerate a load that has an inertia of 80 lb-ft² from 0 to 600 rpm in 5seconds.a. 18.4b. 31.2C.d.a. spacersb. shouldersC.d.28. Which is the least reliable in holding a key in its position?C. set screwd. retaining ringsa.4.59b. 6.1240.1Answer is not among the choices29. A worm gear has 32 teeth and Pd = 6. It mates with a worm rotating 16 times as fast. If the worm diameteris 2.2 inch, determine its lead angle in degrees.c. 7.24d.8.62[

24. The diameter of wire, d = 3/8 in The tensile strength of the wire, S1 = 240 ksi The pressure…

24. A 3/8 in wire rope is made of plow steel having a tensile strength of 240 ksi. For it to have an infinite life, the pressure strength ratio should be 1.4 x 10-³. If the allowable fatigue tension for the rope is 800 lb, determine the minimum diameter of the sheave in inches. a. 12 14 b. 13 15 C. d.

24. A 3/8 in wire rope is made of plow steel having a tensile strength of 240 ksi. For it to have an infinite life, the pressure strength ratio should be 1.4 x 10-³. If the allowable fatigue tension for the rope is 800 lb, determine the minimum diameter of the sheave in inches. a. 12 14 b. 13 15 C. d.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7. A pulley 610 mm in diameter transmits 37 KW at 600 rpm. The arc of contact between the belt and pulley is 144 degrees, the coefficient of friction between the belt and pulley is 0.35, and the safe working stress of the belt is 2.1 Mpa. Find: A. The tangential force at the rim of the pulley. Ans. 1.93 KN B. The effective belt pull. C. The width of the belt used if its thickness is 6 mm. 200 a wide Ans. 1.93 KN Ans. 261 mm
2. A composite shaft is made of slipping a bronze tube of 3-in. outer diameter and 2-in. inner diameter over a solid steel shaft of the same length and 2-in. diameter. The two components are fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 10 ksi for bronze and 14 ksi for the steel? If the hollow tube is made out of steel and the solid shaft is made out of bronze, what is the largest torque that can be carried by the composite shaft if the same working shear stresses are applied? For bronze, G = 6 x 10 psi, and for steel, G = 12 x 10%. T T
1. The endurance limit for rotating shaft, if its ultimate strength Su=1600 Mpa is:
The polar modulus for a solid shaft of 40 mm diameter is
A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and torque applied at both ends is 340 N.m. Determine the angle of rotation in radians.
1. A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the other end. Determine the maximum allowable torque for each material if the angle of twist is not to exceed 6º. Remember to consider both the maximum shear stress and the angle of twist. MATERIAL MODULUS OF RIGIDITY MAXIMUM SHEAR STRESS TORQUE Aluminum 26 GPa 207 MPa Steel 79 GPa 75 MPa Titanium 44 GPa 760 MPa
Find the diameter of the shaft (based on torsional stiffness) for which the angle of twist is not to exceed 1 degree in 20 diameters. The shaft transmits 5 hp and rotates 100 rpm. The modulus of elasticity (shear) is 12,000,000 psi and the modulus of elasticity (tension) is 30,000,000 psi. a. 7.8048 inches. c. 3.6286 inches b. 1.4524 inches d. 5.2462 inches
1. A steel shaft is subjected to the torques shown. The shaft is solid with a diameter of 1 in and G = 12,000 ksi. Determine: (a) internal torque (lb ft) in each segment. Include the necessary diagram to show these internal forces (b) maximum shear stress (psi) in each segment (c) rotation angle of pulley D w/r to the support of A. Follow the rule of signs given in the lecture. Include the necessary FBDs of sections.
The composite shaft shown consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 164 mm and a wall thickness of 7 mm. Steel pipe (2) has an outside diameter of 114 mm and a wall thickness of 6 mm. Both pipes are 3-m long and have a shear modulus of 80 GPa. If a concentrated torque of 20 kN-m is applied to flange B, determine the torque in pipe (1).
1. A 50-mm diameter solid shaft, with a length of 1 meter, is supported at one end and free in the other end. Determine the maximum allowable torque for each material if the angle of twist is not to exceed 6°. Remember to consider both the maximum shear stress and the angle of twist. MAXIMUM SHEAR MATERIAL MODULUS OF RIGIDITY TORQUE STRESS Aluminum 26 GPa 207 MPa Steel 79 GPa 75 MPa Titanium 44 GPa 760 MPa
The composite shaft shown consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 164 mm and a wall thickness of 7 mm. Steel pipe (2) has an outside diameter of 114 mm and a wall thickness of 6 mm. Both pipes are 3-m long and have a shear modulus of 80 GPa. If a concentrated torque of 20 kN-m is applied to flange 8, determine the torque in pipe (1). ... 3 m 3 m 20 kN-m (1) (2) B A 10.98 kN-m в) 15.63 kN-m 9.40 kN-m 14.85 kN-m
The internal diameter of a hollow shaft is 2/3 rd of its external diameter. Compare the strength and stiffness of the shaft with that of a solid shaft of the same material.